c) The temperature measured in the transducer 0(t) at time t seconds is given by:e(t) = (0, + 6,e) vWhere 0; and 0, are temperature values in C° and t= 30s.Evaluate the followingThe temperature across the transducer up to 3 significant figures and in standardform after 12 seconds, if the supply voltage 0, = 65 and 0; = 20 C°.The time t in engineering form and up to 4 significant figures taken for the transducerto have a temperature of 50% of the initial value.If your manager asked you to vary the time constant (t) to make the temperatureequals 30 C° after 5 seconds.Plot the temperature 0(t) using the two different time constants (when t varies from0 to 150 seconds). On the plot show the (maximum and minimum and when theyhappen). Explain what is going on for non-technical audience.1.2.3.4.

We are authorized to answer three subparts at a time, since you have not mentioned which part you…

:) The temperature measured in the transducer 0(t) at time t seconds is given by: e(t) = (6, + 0,e) V Where 0, and 0, are temperature values in C° and t= 30s. Evaluate the following The temperature across the transducer up to 3 significant figures and in standard form after 12 seconds, if the supply voltage 0, = 65 and 0; = 20 Cº. The time t in engineering form and up to 4 significant figures taken for the transduc to have a temperature of 50% of the initial value. If your manager asked you to vary the time constant (t) to make the temperature equals 30 C° after 5 seconds. 1. 2. 3.

:) The temperature measured in the transducer 0(t) at time t seconds is given by: e(t) = (6, + 0,e) V Where 0, and 0, are temperature values in C° and t= 30s. Evaluate the following The temperature across the transducer up to 3 significant figures and in standard form after 12 seconds, if the supply voltage 0, = 65 and 0; = 20 Cº. The time t in engineering form and up to 4 significant figures taken for the transduc to have a temperature of 50% of the initial value. If your manager asked you to vary the time constant (t) to make the temperature equals 30 C° after 5 seconds. 1. 2. 3.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Fig. Q2(b) illustrates the electrical network with passive components. The Vi and Vo are the input and output voltage, respectively. i) Derive the transfer function, G(s) = Vo(s) / Vi(s) then design the combination of resistor, R2, and capacitor, C, that can produce the step response with an overshoot of 10% and a settling time 1.5 ms. ii) The capacitor is completely discharged before the step input voltage (Vi) of 10 volts is supplied to the system. Formulate the output function of Vo in the time domain. Then plot the unit step response of Vo(t) in a graph (t from 0 s to 3 ms). Indicate the settling time, peak time, and maximum overshoot in the graph.
FIND BETA,, S,, S',, Find S'' , using T1 as the temperature at which the parameter values are specified and beta( T2 ) as 20% more than beta( T1
Design a radio receiver that powers an amplification system. The radio signal can be considered as an input voltage, while the amplification system, which is a two-terminal device, can be modeled as an equivalent resistance of 1 kΩ. A bandwidth of 500 kHz and a maximum power frequency of 10MHz are required.a) What is the quality factor?b) Do you consider that your receptor is selective or not very selective?
Refer to the circuit shown, where the op amp is assumed to be ideal. Given that Ra=3 kΩ, Rb=5 kΩ, Rc=25 kΩ, va=150 mV, vb=100 mV, vc=250 mV, and VCC=±6 V, specify the range of Rf for which the op amp operates within its linear region.
a) Derive the governing differential equation for vc(t)
Qa) What is the value of ?(∞)?Qb) What is the equation of V1
An exponential signal has initial value Vi=v(0)=-3[V], final value Vf=(∞)=6[V], and a time constant of 10s. Determine: a) the equation for v(t) b) Graph the function for 0≤t≤100 sec, together with a table of values at 10s (or less) time intervals.
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 10 kΩ, RG = 1 MΩ, RD = 3.9 kΩ, and R3 = 33 kΩ. Calculate the voltage gain for the amplifier if the MOSFET Q-pointis (2 mA, 7.5 V). Assume Kn = 1 mA/V2 and λ = 0.015 V−1.
What is the summing amplifier output voltage vo as shown if v1 =2 sin 1000πt V, v2 = 4 sin 2000πt V, R1 = 1 k , R2 = 2 k , and R3 = 3 k ? What are the input resistances presented to sources v1 and v2? What is the current supplied by the op amp output terminal?
Q.2 (b) A piezoelectric crystal is characterized by a constant, 12 × 10-13 (V/m)/ (N/m2). The diameter of crystal is 8 mm, thickness is 2 mm and leakageresistance is 108 Ω.[1]. Determine the sensitivity of crystal for measurement of displacement inV/m?[2]. Also what will be the output voltage for an input force of 10 N?[3]. If above crystal is connected to an amplifier with input capacitance of 4× 10-10 F and resistance of 108 Ω. The connecting cable has a capacitance of2 × 10-10 F. Determine the time constant for measurement of displacement.[Dielectric constant = 1.250 × 10-8 F/m and Young’s modulus of 1.2 × 10-11N/m2].
The loop gain GH of a closed loop system is given by the following expression K/s(s+2)(s+4), The value of K for which the system just become unstable is ?
a) Keeping in mind the Electrical-Mechanical analogy, write down the angular frequency relation (formula) for an ideal LC oscillator. b) If a Resistance R is added in the LC circuit, Energy is dissipated and it becomes a damped RLC oscillator. Considering the fact that the resistor acts as a damping factor, write down the frequency for the damped harmonic oscillator. c) Under what condition are the two frequencies (in a) and b)) equal?