The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.

The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that…

A: Area of section = (130-20) x 25 = 2750 mm2 Force = 70 kN = 70 x 103 N

Q: 4.5 - Given states I and II, determine the possible values of o and t for which state III = I+ Il…

Q: 120 4090 40 Dimensions in mm Im 2AN Determine the maximum tensile stress in the beam shown. O 7.31…

A: To find maximum tensile and compressive stress

Q: The pipe shown, has an inner diameter of 80mm and an outer diameter of 100mm. If its end is…

A: ASKED: To determine the shear stress at the inner and outer walls of the pipe. Given, Outer…

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

Q: A fire extinguisher tank is designed for an internal pressure of 986 psi. The tank has an outer…

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A: We will solve this question in step no. 2

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Given the following data: Cross section: 50mm x 75mm P= 200 kN e = 15° with the x-axis a. Find the…

A: solution Given Data P=200 kNθ=150Cross section = 50mm×75mm

Q: A fire extinguisher tank is designed for an internal pressure of 899 psi. The tank has an outer…

A: Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses…

Q: Angle 1 Tyx Txy Tye Figure 1 Point B- x-direction stress 60MPA(tension), y-direction stress…

Q: Given the following data: Cross section: 50mm x 75mm P = 200 kN θ = 15 ° with the x-axis Find…

A: Draw the 2D diagram of the stress element. Calculate the stress in the x-direction.…

Q: 1. Given the following data: Cross section: 50mm x 75mm P = 200 kN e = 15° with the x-axis a. Find…

A: For a Member ,Inclimed at an angle θ from Horizontal or Any Axis:1-Tensile Stress σ=PACos2θ.2-Shear…

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: simply supported wood beam with overhang is subjected to uniformly distributed load q. * Inserted…

Q: The d = 15-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When…

Q: The steel rod has a radius of 1.25 in. If it is subjected to a shear of = 5 kip, determine the…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Calculate principal stresses at point

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: to find - absolute maximum shear stress from given principal stresses.

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: Given the following data: Cross section: 50mm x 75mm P = 200 kN θ = 15 ° with the x-axis Find the…

A: P= 200 kN Cross section A= 50 x 75 mm θ= 15° with the x axisStress = PA=200×10350×75Stress σ= 53.33…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and…

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: To lower ends of the three bars in the figure two are the same level before the rigid homogeneous…

A: In the question given above, Total weight of the blockW =176 knThus , Ps +Ps+Pb=176 knAs the loading…

Q: Situation 6: A solid shaft is partially inserted in a hollow shaft where it snuggly fits and is…

Q: 11-95. The beam has the rectangular cross section shown. If w = 1 kN/m, determine the maximum…

A: Given: The value of w is 1 kN/m. Consider the figure,

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: 5. Calculate the depth of neutral axis at balanced condition if the effective depth is 250 mm and…

A: Note- We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: The shaft is hollow from A to B and solid from B to C. The shaft has an outer diameter of 80 mm, and…

A: Given: The outer diameter of the shaft is 80 mm. The thickness of the wall is 10 mm. The shear…

Q: A water tank 12 14 is completely filled with water. Determine the minimum thickness of the plate if…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: A water tank, 22 ft in diameter, is made from steel plates that are 1/2 in. thick. Find the maximum…

A: Given:- A water tank, 22 ft in diameter, is made from steel plates that are 1/2 in. thick. Find the…

Q: A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the…

A: Crossection of Ab = 50mm x 50mm Hollow section with outer dimater = 50mm Load on the Ab and Bc…

Q: Q2:The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in…

A: Given data Clockwise torque Anticlockwise torque Diameter To find Maximum shear stress Stress…

Q: Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P…

A: F2 = - R +2Q = - 13 + (2 x 5) = - 3 KN F1 = - R + 2Q-2P = - 13 + (2 x 5)-(2 x 15) = - 33 KN

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: The cross section of the CD part of the crane boom in the picture is a standard 50x150mm2. Determine…

Q: Point Ax-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear…

A: a) Stresses at 30o σx'=σx+σy2+σx-σy2cos2θ+τxysin2θ =(-60)+(-40)2+(-60)-(-40)2cos2×30°+30 sin2×30°…

Q: Compute the maximum shear stress

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: To find out the absolute maximum shear stress. Given data, A) (σp)1 = 2780psi (σp)2 = -2440…

Q: a) Compute the major principal stress. b) Compute the minor principal stress. c) C) Compute the…

A: Given, σx =150kpaσy =50 kpaτxy =50 kpaθ = 10°

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: 10 mm 10 mm ㅑㅑ 50 mm 50 mm 10 mm B 150 mm 10 kN 250 mm C 10 kN 150 mm D

A: This question is from from solid mechanics here we are given with a simply supported beam with…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that…

A: Bearing stress:σb=ForceArea of bearing

Question

The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15^o with the x-axis.

What is the tensile stress of section AA’?
Determine the shear stress on plane AA’
At what angle of plane AA’ is the shear maximum.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
Given the following data: Cross section: 50mm x 75mm P = 200 kN θ = 15 ° with the x-axis Find the tensile stress (in MPa) on plane A-A. Find the shear stress (in MPa) on plane A-A. Find the angle (in degrees) of plane A-A in which the shear stress is maximum.
Compute the deformation in member 1 which is solid alumnim with a area of 214159 mm^2
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
A rectangular bar, 25mm x 50mm in cross-section, is subjected to an axial tensile force P = 80kN. If plane A-A makes an angle of 30° with the horizontal plane, determine the shear stress on plane A-A [in MPa].
A cantilever beam of length 1m carries a point load of 1900N at the free end. The cross-section of the cantilever is an unequal angle of dimensions 100mm by 60mm and 10 mm thick. The small leg of angle (i.e 60 mm) is horizontal. The load passes through the centroid of the cross-section. Determine: (i) Position of neutral axis; (ii) The magnitude of maximum stress set up at the fixed section of the cantilever.
The pipe shown, has an inner diameter of 80mm and an outer diameter of 100mm. If its end is tightened against the support at A using a torque wrench at B, determine the shear stress developed in the material at the inner and outer walls along the central portion of the pipe when the P (in newtons) forces are applied to wrench. P=74 Show detailed solution
The bell-crank mechanism shown in Figure P1.33 is inequilibrium for an applied load of P = 7 kN at A. Assume that a =200 mm, b = 150 mm, and θ = 65°. Determine the minimum diameterd required for pin B for each of the following conditions:(a) The shear stress in the pin must not exceed 40 MPa.(b) The bearing stress in the bell crank must not exceed 100 MPa.
The normal stress (kN/cm2) at the K point resulting from the tensile force of P=1000 kN acting from the point B (in the z direction) eccentrically on the I section with dimensions b=30 cm, h=50 cm and t=5 cm shown in the figure below. calculate.
Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
14-2.5: The stress-strain curve of the axially loaded bar BC is binary and linear, with ϭA=400 MPa, ϭ=500 MPa ,ꜪA=0.004, Ꜫ= 0.016 . Find the total axial displacement at point C. External loads P1=1.6 kN, P2=1.2 kN, cross-sectional area A=10 mm2, bar dimensions a=600 mm, b=300 mm
Q36 onlys Ratio of stress in part A and B