Solve fast please The thickness of a wall is 0.07 m.lt is exposed toToo=310K air and T=300K ambient air.if the outersurface temperature of the wall (right side) is 500 K,and the heat convection coefficient is h=30 Ww/M²K,the emissivity rate is 0.78, and the heat transmissioncoefficient of the wall is k=0.86 W/mK, what is thetemperature of the inner wall?

Answered: Image /qna-images/answer/b0408896-3372-4074-ac13-ead41080dcfb.jpg

Answered: The thickness of a wall is 0.07 m.lt is…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.18P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
1.21 In an experimental set up in a laboratory, a long cylinder with a 5-cm diameter, and an electrical resistance heater inside its entire length is cooled with water flowing crosswise over the cylinder at and a velocity of 0.8 m/s. For these flow conditions, 20 kW/m of power is required to maintain a uniform temperature of at the surface of the cylinder. When water is not available, air at is used with a velocity of 10 m/s to maintain the same surface temperature. However, in this case, the cylinder surface heat dissipation rate is reduced to 400 W/m. Calculate the convection heat transfer coefficients for both water and air, and comment on the reason for the differences in the values.
Question 1:A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg=1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15oC and -20oC, respectively, ona cold winter day, what is the rate of heat loss throughthe glass? To reduce heat loss through windows, it iscustomary to use a double pane construction in whichadjoining panes are separated by an air space. If thespacing is 10 mm and the glass surfaces in contact withthe air have temperatures of (last two digit of your Registration number) oC and -15oC, what isthe rate of heat loss from a 1 m x 2 m window? Thethermal conductivity of air is ka=0.024 W/m.K.
A household oven door of 0.4 m height and 0.6 m width reaches an average surface temperature of 50°C during operation. Estimate the total heat loss to the room with ambient air at 22°C and convective heat transfer coefficient 5 W/m².K, if the door has an emissivity of 0.83 and the surroundings are also at 22°C.
As seen in the attached figure, a 5-mm-diameter spherical ball (k = 15 W/m·K, Cp=480 J/kg·K) at 50°C is exposed to a medium at 15°C, with a combined convection and radiation heat transfer coefficient of 20 W/m2·K (to be used for option a and b) a) If the ball is covered by a 1-mm-thick plastic insulation (k = 0.13 W/m·K), determine whether the plastic insulation on the ball will help or hurt heat transfer from the ball. b) Assume that the ball is initially at uniform temperature of 50 °C. Determine how long it will take for the center of the ball to drop to 20 °C.
Water at 5°C is being used to cool apples from an initial temperature of 25° to 10°C. Thewater flow over the surface of the apple creates a convective heat-transfer coefficientof 15 W/(m2-K). Assume the apple can be described as a sphere with a 10 cm diameterand the geometric center is to be reduced to 10°C. The apple properties include thermalconductivity of 0.45 W/(m-K), specific heat of 3.950 kJ/(kg-K), and density of 940 kg/m3.a. Determine the time that the apples must be exposed to the water.b. If the apple is submerged only for 2 hours, what will be its center temperature?
A transformer that is L=20cm long, 6.2 cm wide, and 5 cm high is to becooled by attaching a 10 cm × 6.2 cm wide polished aluminum heatsink (emissivity =0.03) to its top surface. The heat sink has seven fins,which are 5 mm high, 2 mm thick, and 10 cm long. A fan blows air at25°C parallel to the passages between the fins. The heat sink is todissipate 20 W of heat and the base temperature of the heat sink is notto exceed 60°C. Assuming the fins and the base plate to be nearlyisothermal and the radiation heat transfer to be negligible, determinethe minimum free-stream velocity the fan needs to supply to avoidoverheating. (k=0.02681W/m˚C, Pr=0.7248, V= 1.726×10-5 m2/s, )

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning