The three parallel loads in the circuit shown below can be described as follow: Load 1 is absorbing an average power of 7.5kW and +7KVAR; Load 2 is absorbing an average power of 2.1kW and generating 2KVAR of magnetizing reactive power; Load 3 has 48 + 19.2j ohms impedance. Assum Vo = 480 angle 0 Vrms. Determine the total current drawn from the source. j0.5 N V. L, L2 L3

The three parallel loads in the circuit shown below can be described as follow: Load 1 is absorbing an average power of 7.5kW and +7KVAR; Load 2 is absorbing an average power of 2.1kW and generating 2KVAR of magnetizing reactive power; Load 3 has 48 + 19.2j ohms impedance. Assum Vo = 480 angle 0 Vrms. Determine the total current drawn from the source. j0.5 N V. L, L2 L3

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30P: Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source....

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source. Load 1: Inductive load, 125kVA,0.28PF lagging. Load 2: Capacitive load, 10kW,40kvar. Load 3: Resistive load, 15kW. (a) Determine the total kW, kvar, kva, and supply power factor. (b) In order to improve the power factor to 0.8 lagging. a capacitor of negligible resistance is connected in parallel with the above loads. Find the kvar rating of that capacitor and the capacitance in F. Comment on the magnitude of the supply current after adding the capacitor.
Three loads connected in parallel across a 1000-V (RMS), 60-Hz single-phase source.Load 1: Inductive load, 125 kVA, 0.28PF laggingLoad 2: Capacitive load, 10 kW, 40 kVARLoad 3: Resistive load, 15 kWa) Determine the total kW, kvar, kva, and supply power factor.b) In order to improve the power factor to 0.8 lagging, a capacitor of negligible resistance isconnected in parallel with the above loads. Find the KVAR rating of that capacitor and thecapacitance in μf .c) Comment on the magnitude of the supply current after adding the capacitor
A 15kV, 3 phase circuits feeds a load of 10,000 kW at a lagging load factor and the load current of 750A. If it is desired to improve the power factor, determine the following: The uncorrected power factor;Reactive load;The new corrected power factor after installing a shunt capacitor unit with a rating of 9000 kVAR. (a) 0.813 lagging (b) 14723 kVAR (c) 0.9 lagging (a) 0.613 lagging (b) 15723 kVAR (c) 0.75 lagging (a) 0.713 lagging (b) 13723 kVAR (c) 0.85 lagging (a) 0.513 lagging (b) 16723 kVAR (c) 0.80 lagging
ANSWER IN POLAR FORM AND 2 DECIMAL In the circuit shown in Figure 1, a load having an impedance of 37 + j26 Ω is fed from a voltage source through a line having an impedance of 1 + j7 Ω. The effective, or rms, value of the source voltage is 250 V. a. Calculate the load current IL and the voltage VL (current and voltage at the load) b. Calculate the average and reactive power delivered to the load. c. Calculate the average and reactive power delivered to the line. d. Calculate the average and reactive power supplied by the source
A 120V (rms), 60Hz three-phase system is supplying power to the following two loads: Load # 1: A balanced load connected in wye with 100ohm resistance and 0.1H inductor connected in series. Load # 2: A balanced load connected in delta with 100ohm resistance and 10uF capacitor connected in series. Draw a circuit diagram and Determine: (i) Total active and reactive power supplied to load # 1 by the system (ii) Total active and reactive power supplied to load # 2 by the system (iii) Magnitude of the total current supplied by the source (iv) Source power factor
Calculate the real and reactive powers of the load between terminals a and b in the given figure. Assume f = 60 Hz, V∼S�∼� = 70∠0 V rms, RS = 2 ohm, Ro = 26 ohm, and XL = 5 ohm. The real and reactive powers are _______W and _________VAR.
The following information is given in connection with three loads that are connected in parallel to a 230 volts ac line. Load 1: 4.6KW at unity power factorLoad 2: 11.5KVA at lagging power factor of 0.62Load 3: 5.52KW at leading power factor of 0.8 Calculate the:a. Total currentb. Overall power factor c. Total power d. Total reactive power e. Draw the phasor diagram of the current
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, andadmittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. draw the circuit diagram
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, and admittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal place.Thank you!
3) Suppose a voltage ?(?) = 2 × 120 sin(377? + 30°) is applied to a single phaseload, and the resulting current is i t = 2 × 10 sin(377? − 30°).(i) Find complex power S, average power P, reactive power Q and circuit power factor.(ii) Find a simple series circuit which exhibits this behavior.(iii) Find a simple parallel circuit that will exhibit this behavior.
A 3-phase Y-connected load draws power from a 3-phase Y-connected source. The source voltage, ?=440∠0º?_rms and the load impedance, Z_y=(30+j15) Ω. The line impedance, Z_line= (1+j1)Ω and the system operates at 60 Hz. a) Draw the single-phase equivalent circuit and label all given quantities numerically. b) Calculatethe rms line (phase) current phasor in each phase. c) Calculate the total active or real power supplied by the source. d) Calculate the total active or real power consumed by the load. e) Calculate the total line loss i.e. the total activepower lost due to line. f) Determine the power efficiency of the system.