150 A{80t=02Σ120 Ω800 V+10 Q2V40 2 40 mH-The topic for this problem is forced response. Theswitch is connected to position 1 for a very long timebefore moving to position 2 at t=0.a.What is v, before and after the switch changedposition?b.What is it before and after the switch changedposition?C. What is v, and i, at t = ∞o?d. What is the Thevenin resistance seen by theinductor for t>0?What is the time constant of the circuit fort>0?What is i, at t = 1.5 ms? (Hint: use thecomplete response formula)e.f.

Answered: Image /qna-images/answer/3e43954f-5e5b-4776-9566-b6f339d51ada.jpg

Answered: The topic for this problem is forced…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a series r-c circuit takes a current whose equation is i=0.85sin(754t+pi/4) when connected to a source of emf having the equation e=340sin754t. calculate the capacitance of the capacitor, circuit power factor, and power.
Question 5 Use the node-voltage method to find the steady-state expression for v_0(t) in the circuit belowif v_g1 = 25 sin (400t + 143.15◦)V v_g2 = 18.03 cos (400t + 33.69◦)V
H = 3RM2cos(9ft) where f = frequency, t = time, and the remaining variables are either proportionality constants or material constants. What is the maximum value H could have (algebraic answer)
Closed loop poles in a second order system -3 + 4j and -3-4j If so, what is the damping rate of the system? 3/44/35/45/33/5one4/50
Find the impedance theoretically of a wire if it carries the frequency 10 kHz have a voltage is 8v, the current is 2mA, resistance is 12 kΩ , inductance 27 mH and capacitance 0.2 µf
A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε =Va - Vb = εmsinωt, where εm = 120 V and ω = 726 radians/second. The values for the remaining circuit components are: R = 62 Ω, L = 95.6 mH, and C = 13.8μF. 4) What is t1, the first time after t = 0 when the voltage across the inductor is zero? 6) What is VC = Vd - Va, the voltage across the capacitor, at time t = 0? Note that VC is a signed number.
A capacitor and a 30-ohm resistor are connected in series. What is the equation of the resulting current if that capacitor has a capacitance of 80 microfarads and the combination is placed across a power supply whose equation is e = 325 sin (314t)? a.) i(t) = 6.52 sin (314t - 53°) b.) i(t) = 6.52 sin (314t + 53°) c.) i(t) = 6.53 sin (314t + 52°) d.) i(t) = 6.53 sin (314t - 52°)
The circuit shown below has two inputs: v1(t) = 50 cos (20t – 75°) V v2(t) = 35 cos (20t + 110°) V When the circuit is at steady state, the node voltage is v(t) = 21.25 cos (20t – 168.8°) V Determine the values of R and L.
Show that at a given frequency ω, the circuits will have the same impedance between the terminals a,b ifR1=R21+ω2R22C22,C1=1+ω2R22C22ω2R22C2.2. Find the values of resistance and capacitance that when connectedin series will have the same impedance at 40 krad/s as that of a1000 Ω resistor connected in parallel with a 50 nF capacitor.
A 200 Ω resistor, 0.900 H inductor, and 6.00 µF capacitor are connected in series across a voltage source that has voltage amplitude 30.0 V and an angular frequency of 250 rad/s. (a) What are v, vR, vL, and vC at t = 20.0 ms? Compare vR + vL + vC to v at this instant. (b) What are VR, VL, and VC? Compare V to VR + VL + VC. Explain why these two quantities are not equal.
Electrical Engineering A cylindrical hollow pipe is made of steel (μr = 180 and σ = 4 x10^6 S/m).The external and internal radii are 7 mm and 5 mm. The length of the tube is 75 m.The total current I(t) flowing through the pipe is:I(t)= 8 cos(ωt) with ω=1200π rad/sDetermine:d) The intrinsic impedance of the good conductor. Remember that: Transcribed Image Text:η = = √2/45° σ·δ
In the circuit shown below, the switch is connected to the battery at t = 0 and returns to potential of earth at t = 20 ms. Determine:a)The expression of the input voltage in the time and frequency domain, v(t) and V(s).b)The circuit impedance Z(s) = V(s)/I(s).c)The current expression, i(t).

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS