The total rms output voltage of a single-phase bridge inverter operating from a nominal 200V DC supply is to be kept constant at 100V. If the supply voltage varies from 180 to 200V. Calculate: 1. 2. The range of conduction pulse widths (2d). For nominal input voltage find rms value of fundamental output voltage and rms value of 3rd harmonic in the output.

The total rms output voltage of a single-phase bridge inverter operating from a nominal 200V DC supply is to be kept constant at 100V. If the supply voltage varies from 180 to 200V. Calculate: 1. 2. The range of conduction pulse widths (2d). For nominal input voltage find rms value of fundamental output voltage and rms value of 3rd harmonic in the output.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A square-wave inverter has an R-L load with R=15 Ω and L=10 mH. The inverter output frequency is400 Hz (fundamental frequency).(a) Determine the values of the required to establish a load current which has a fundamentalfrequency component of 10 A rms with α = 0.(b) For a controlled full-bridge inverter, the dc source is 125 V and the switching frequency is60 Hz. Determine the value of α to produce an output with amplitude of 100 V at the fundamentalfrequency.
A single phase half bridge inverter is operating from a 25 V DC source and supplies power to resistive load. What is the distortion factor of fundamental output voltage?
Justify the usage of the RCD (residual current device ) at the AC side of the inverter? You have to explain its operation prinviple
Redesign the resistive load inverter for operation at a power level of 0.30 mW withVDD = 3.3 V. Assume VT O = 0.7 V. Keep theother design parameters the same. What is the newsize of MS and the value of R? (b) What are thevalues for NMH and NML ?
If,for a single phase half bridge inverter the amplitude of output voltage is Vs and the output power is P then their corresponding values for a single phase full-bridge inverter are a. 2Vs,2P b. 2Vs,4P c. 2Vs,P d. Vs,P
Design an asymmetrical inverter to meet the delay specificationa symmetrical CMOS reference inverter to provide a delay of 1 ns when driving a 10-pF load.(a) Assume VDD =2.5 V. (b) Assume VDD =1.8 V and VT N =−VT P =0.45 V. with (W/L)P = 2(W/L)N .
A CMOS inverter shown in Figure below, with kn = 10, k, = 100 JA/V?, and V, = 0.5V having a sinusoidal signal source with Thevenin equivalent voltage of 0.075V as peak amplitude and resistance of 150k. Determine the signal values at node A with V = +1.5V. (a) 6.82m V (b) 8.62mV (c) 6.80m V (d) 8.80mV
What is the switching threshold (where does vI = vO) for a minimum size inverter in which both W/L ratios are 2/1 if VDD = 1.8 V and VTN = −VTP = 0.45 V?
Sketch the VTC for a logic inverter with VoH = 5 V, Vol = 0.2 V, V.IL= 1.4 V, and VIH= 1.6 V. Also, determine the logic swing , transition width, and the noise margins.
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. Sketch the waveforms of load voltage, fundamental component of load voltage, fundamental component of load current, current through any one device and voltage across any device .
1 phase half bridge inverter having dc input voltage 300V , and purely resistive load R = 2.4 ohm , find :Vrms for the first harmonic fundamental load power: average supply current if the power delivered by each source is 3.8 kw :
Design an asymmetrical inverter to meet the delay of 250 ps for a load capacitance of 120 fF. Use VDD =1.5V, VTN =0.50 V, and VTP =−0.50 V. with (W/L)P = (W/L)N .