The transit with f/i = 100 and f+c = 1.0 was set up at point P with elevation 91 m. Point A is observed with stadia intercept of 1.26 m. The recorded vertical angle is -4° on 1.65 m. What is the elevation of point A? The height of instrument is 1.5 %3D 82.01 O 74.34 96.34 86.45

The transit with f/i = 100 and f+c = 1.0 was set up at point P with elevation 91 m. Point A is observed with stadia intercept of 1.26 m. The recorded vertical angle is -4° on 1.65 m. What is the elevation of point A? The height of instrument is 1.5 %3D 82.01 O 74.34 96.34 86.45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 8. Explain the reason for salinity levels shown in the diagram below. Baltimore Chter Washington…

A: The area near the Norfolk is darkish blue showing most saline area in the figure. The reason for…

Q: rigure Q3 shows the cross section of an existing road in a flat rural area. a) Briefly explain the…

Q: 2.49 The negligible weight rigid bar BCD is supported by two steel cables with the same cross…

Q: The ratio of saturated unit weight to dry unit weight of a soil is 1.25. If the specific gravity of…

Q: A mat foundation is in plan 40 m x 40 m with a thickness of 1.2 m. The total column and bearing wall…

A: ASKED: To compute the average gross bearing pressure and the average net bearing pressure for the…

Q: Datermine the horizontal and vertical components of reaction at the supports. Neglect the thickness…

A: Length of simply supported beam, L=6mThe external loads are 5KN, 4KNtension in rope.The left end…

Q: 1. Convert the following Azimuths to Bearings: a. 10° 20' b. 108° 46' c. 218° 07' d. 334° 35' e.…

Q: Q.2 The weight fraction of glass in a glass/epoxy composite is 0.8. If the density of glass and…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A bridge, as shown below, shall carry a distributed load of 280 kN/m2. For the given load and…

Q: The total unit weight of the glacial outwash soil is 16 kN/m3. The specific gravity of the solid…

Q: A sheet of water of thickness 1 m is available to fill the voids of cohesionless soil to a degree of…

Q: Assuming the pavement condition and cross section remain constant. The terrain is also constant…

A: e + f = V2/(225R) ; here e = 0.07{max super elevation} , f = 0.15{lateral friction}, R = radius of…

Q: 1,83 KN 1,83 kn 693 KN 1,83 KN 0,316 KN A A25m 9 KN 1,25m 4. ;25m 3,25m @ FIND THE REACTIONS (2)…

Q: In a consolidation test, the void ratio of the specimen which was 1.068 under the effective pressure…

Q: 1. Is there a difference between the values of Qideal Calculated by equation (1) and Qat using…

A: Note: As per guidelines for multiple questions only one question can be answered. So for other…

Q: A timber beam 150 mm wide by 250 mm deep is

Q: beam bhnown, رشث متا و این( a. draw SFD and BMD, b. prove that for the isosceles:, Tmax. = bh C. if…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions posted, need to be…

Q: B. Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and…

Q: The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider…

Q: Q.2 A, B, C and D are the activities of a network. Their normal and crash durations (in days) are…

Q: In how many ways can a bowling player score in one throw of a bowling ball. (There are 10 pins) O…

A: Answer We can use Computations to find the number of ways for a bowling player to score which is…

Q: Question 2 a) Name the four control measures an engineer can implement to encourage traffic calming?…

A: Brief concept introduction- Traffic- Pedestrians, riding or herding animals, cars, trailers, and…

Q: Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial…

Q: A four-lane rural freeway segment has a 510 m grade length of 2% upgrade followed by a 630 m grade…

A: BFFS = 110KMPH = 110/1.609 = 68.36mil/hr

Q: A builtup steel beam comprise of two flange plates 250 mm wide × 10 mm thick and web plate 330 mm…

Q: may be assumed to be as follows: A to B = 0.6; B to C = 9 29 29 ;D to E = 9. Find the flow rate and…

A: To find:- flow rate pressure at C

Q: 554. What safe value of W can be applied to the beam loaded as shown in Fig. P-554 if o, < 60 MPa…

A: step 1-

Q: 1.7.4 Relationship between moisture content, bulk density, and CBR for crushed aggregate to be used…

Q: Find the reactions at the beam ends 'A' and 'B'. The beam is 6ft in length and the distributed load…

Q: 6. Discussion: 1. Is there a difference between the values of Qideal calculated by equation (1) and…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: رشت تا فياين( Fur the beam shown, a. draw sFD and BMD, b. prove that for the isosceles:, max. = bh…

A: Given : Support Reaction : ∑MD = 0 ⇒ RB×6 - 40 - 2×3×32+6 - 12×3×3×33+6 = 0…

Q: Compute the vertical stress increments under Points A, B,

Q: Find the optimum duration and cost for the projects of a 8 activities? No. Activity Durations and…

Q: From a point outside an equilateral triangle, the distances to the vertices are 10 m, 18 m and 10 m,…

Q: A sheet of water of thickness 1 m is available to fill the voids of cohesionless soil to a degree of…

Q: PROBLEM NO. 3 For an inorganic soil, the following grain size analysis is given: U.S. Sieve No.…

A: Solution: Given: U.S. Sieve No. Diameter m(m) % Passing 4 4.75 100 10 2 90 20 0.85 64 40…

Q: A catchment is made of 60% area

A: Given: Area 1 = 60 % Runoff Coefficient, r1= 0.6 Area 2 = 40 % Runoff Coefficient, r2= 0.4 The…

Q: Ex. 4 The solid hom gencons 400 1b block A a hurizontal plane. The coefficint of Paction botuean the…

Q: A water tower is constructed on a circular raft 5 m in diameter at a depth of 2 m below ground-level…

Q: Given the Truss as shown below with 0 = 45°. Using Method of Joints, determine the forces at the…

Q: Dosage of alum with the alum-lime coagulation of a water is 50 mg/l. It is desired to react only 10…

Q: The ionic character of a groundwater is defined by the following hypothetical combinations:…

A: Given data- concentrations-Ca(HCO3)2=3.0 meq/LMg(HCO3)2=0.4 meq/LMgSO4=0.8 meq/LNa2SO4=0.2…

Q: A retaining wall 9 m high, with its back face smooth and vertical. It retains sand with its surface…

Q: termine the required spacing of 10 stirrups at the left end of a s anning 6 m. subjected to the…

A: Given Data:L=6mDead load=50kN/mLive Load = 70kN/mfc=30mpafy = 240mpab=300mmeffective depth d=…

Q: A cantilever beam of length L and a cross section with shape factor f supports a concentrated load P…

Q: What is the difference between a contract and an agreement?

A: Answer:-

Q: Topic: Shear and Moment Diagram Solve 5 problems (following the conditions stated below) involving…

Q: b 1- Shear failure occur when oz Oh > oy OH > Oy > oh Oy > OH > Ơh 5- Tensile Failure Vertical…

A: Brief concept introduction- Shear failure- It occurs when the shear stress developed in the…

Q: The Froude number of a flow in a triangular channel (vertex angle 90°) is 0.8. If the depth of flow…

Q: A- Two velocity components are given in the following case, find the third components such that it…

Concept explainers

Pressure and Stress

Question

The transit with f/i = 100 and f+c = 1.0 was set up at point P with elevation 91 m. Point A is
observed with stadia intercept of 1.26 m. The recorded vertical angle is -4° on 1.65 m. What is
%3D
the elevation of point A? The height of instrument is 1.5
O 82.01
O 74.34
96.34
86.45

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A triangular piece of land ABC (clockwise) has the following directions in azimuth fom South. AB = 225o23’, BC = 325o20’, CA = 100o10’ Compute the interior angles. 2. An open traverse ABCDE has following azimuth from South: AB = 250o30’ BC = 280o20’ CD= 210o45’ DE = 150o50’ Required: Deflection angles at points B,C, and D. Draw the figure properly.
An open traverse that runs from A to G has the following deflection angles:B = 52⁰ 25’ L; C = 50⁰ 20’ R; D = 49⁰ 30 ‘ R; E = 73⁰ 20’ L; F=140⁰ 10’ R. If the bearing of line AB is N. 25⁰ 20’ E., compute the azimuth and bearing of the remaining lines.
To test its line of sight adjustment, a level is set up near C (elev. 193.436 m) and then near D. Rod readings listed in the order taken are C = 1.315 m, D = 0.848 m, D = 1.296 m, and C = 1.767 m. Compute the elevation of D, and the reading required on C to adjust the instrument.
The following are bearings taken on a closed loop traverse. Compute the interior angles and correct them for the observational errors. Assuming the observed bearing of the line AB to be correct, adjust the bearings of the remaining sides. Line Bearing AB S37o 30´ E BC S43o 15´ W CD N73o 00´ W DE N12o 45´ E EA N 60o 00´ E
prove the formula of the combined correction for earths curvature and refraction Hcr = 0.0675 D^2 where: Hcr= combined correction D = horizontal distance
compute for 1.)Azimuth 2.) Interior Angle at B 3.)Angle to the right
ABCDA is a clockwise closed traverse. ͦ̂ͦGiven: XA=YA=200.00 m, Azimuth ??? = 290, the angle ??? = 270 (angles in degrees) The data is as followsa. Draw the figure.b. Adjust the angles.c. Compute azimuths of all sides.d. Adjust the traverse and compute coordinates of the traverse station.
ABCDA is a clockwise closed traverse.Given: XA=YA=200.00 m, Azimuth ??? = 290, the angle ??? = 270 (angles in degrees) The data is as followsa. Draw the figure.b. Adjust the angles.c. Compute azimuths of all sides.d. Adjust the traverse and compute coordinates of the traverse station.
A loop traverse ABCDE with a bearing on course DE of S 71 degree 42 minutes 15 seconds E, and the following angles: A= 60 degrees 53 minutes 30 seconds, B= 215 degrees 58 minutes 0 seconds, C= 65 degrees 10 minutes 10 seconds, D= 110 degrees 00 minutes 00 seconds, E= 86 degrees 58 minutes 45 seconds. Compute the angular error and adjust the angles as needed.
The azimuth from north of traverse line AB is 225 degrees and 00". If the succeeding line BC has a bearing of S 30 degrees and 00" E. Compute the following: a. Bearing line AB b. Deflection of station B
Calculate the following: a. Bearing AB b. Deflection angle CB c. Azimuth from the north of DE
From the following differential leveling notes, compute the difference in elevation between stations 5 and 6. a. 2.62 b. 1.61 c. 3.51 d. 1.87