The trapezoidal cross-section of a curved beam is shown below. 25 mm 30 mm 25 mm 45 mm If the distance of the outside edge to the axis of curvature is 100 mm, locate the centroidal axis and the neutral axis of the cross-section. Also, calculate the bending stress at the inner and outer points on the cross section, and the stress at point A as shown, if the cross-section carries an internal bending moment of 200 N.m.

The trapezoidal cross-section of a curved beam is shown below. 25 mm 30 mm 25 mm 45 mm If the distance of the outside edge to the axis of curvature is 100 mm, locate the centroidal axis and the neutral axis of the cross-section. Also, calculate the bending stress at the inner and outer points on the cross section, and the stress at point A as shown, if the cross-section carries an internal bending moment of 200 N.m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Given: Maximum positive shear = 387.50 kN Maximum negative shear = 602.50 kN Maximum positive moment = 1970.65 kN-m Maximum negative moment = 1480 kN-m Location of maximum shear from the left end of beam = 22 m Location of maximum moment from the left end of beam = 15.23 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
a. Calculate the moment of inertia (I) of the given cross–section b. Calculate the first moment of area (Q) at certain depth by using 25 mm increments. c. Calculate and draw the horizontal shear stress distribution of the beam at 0.2 m from the left support
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
Consider a 125-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 60 kN-m and 68 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 160 mm, b2 = 30 mm, b3 = 255 mm, d1 = 75 mm, d2 = 220 mm, d3 = 75 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Consider a 155-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 79 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 135 mm, b2= 50 mm, b3= 205 mm, d1= 65 mm, d2= 180 mm, dz= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".