The two-wattmeter method produces wattmeter readings P2 = 800 W Wand P1= 560 W when connected to a delta-connected load. If the line voltage is 208 V, calculate: (a) the total average power, (b) the total reactive power, (c) the power factor, and (d) the phase impedance. PLEASE GIVE ME YOUR ANSWER AND SOLUTION IN 3 DECIMAL POINTS!

The two-wattmeter method produces wattmeter readings P2 = 800 W Wand P1= 560 W when connected to a delta-connected load. If the line voltage is 208 V, calculate: (a) the total average power, (b) the total reactive power, (c) the power factor, and (d) the phase impedance. PLEASE GIVE ME YOUR ANSWER AND SOLUTION IN 3 DECIMAL POINTS!

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Similar questions

In the circuit of figure shown in the next slide, three impedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0 ohms, connected between conductors a, b, c and the neutral “n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABC system. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance
1. A balanced, three-phase, 900V system is supplying a balanced load connected in delta. A three-phase wattmeter (measuring total three-phase power) is connected to the supply and an ammeter is connected to one of the supply phases. Each load consists of a resistance in parallel with an inductive reactance. a. If the wattmeter reads 14.1 kW, what is the resistance of each load? b. If the ammeter reads 10 A What is the impedance (Z) of each load? c. What is the reactance (X)? d. If this load was instead connected in star, what would the new readings be? (P and I).( need only handwritten solution .otherwise downvote.)
The balanced three-phase load shown is fed from a balanced, positive-sequence, three-phase Y-connected source. The impedance of the line connecting the source to the load is negligible. The line-to-neutral voltage of the source is 7200 V. 1. a) Find the reading of the wattmeter in watts. 2. b) Explain how you would connect a second wattmeter in the circuit so that the two wattmeters would measure the total power. 3. c) Calculate the reading of the second wattmeter. 4. d) Verify that the sum of the two wattmeter readings equals the total average power delivered to the load.
A three-phase, four-wire, wye-connected system supplies a noninductive lighting load only. The current in line A is 8 A, in line B the current is 10 A, and in line C the current is 6 A. The voltage from each line wire to the neutral wire is 120 V. Determine: the power, in watts, indicated by each of the three wattmeters. the total power, in watts, taken by the entire lighting load
A d.c. 3-wire system is to be converted into a 3-phase, 4-wire system by adding a fourth wire equal in X-section to each outer of the d.c system. If the percentage power loss and voltage at the consumer's terminals are to be the same in the two cases, find the extra power at unity power factor that can be supplied by the a.c. system. Assume loads to be balanced.
At the supply side, the line current was measured as 25A and lags the corresponding line-to-neutral voltage by 30 deg. Shown VL is between lines A and B. 1. What is the total real power in kW delivered by the supply? 2. What is the per-phase impedance in ohms, of the unknown delta connected balanced load? 3. If a wattmeter is connected at the source side: Voltage probe measures VAB, and current problem Measures IAa, what will be the wattmeter reading in watts?
Two wattmeters are used to measure the total power drawn by a balaced delta connected load. If the wattmeters read 1200 W and 800 W respectively, and the line to line voltage is 208 V, solve for the impedance per phase of the load.
2. Solve the following problem: A THREE-PHASE PLANT CONSUMES 600 KVA, WITH A VOLTAGE OF 2400 VOLTS AND A POWER FACTOR OF 0.8 BEHIND. a) DETERMINE THE EQUIVALENT DELTA IMPEDANCE OF THE PLANT. b) IF THE PLANT WERE A STAR, CALCULATE THE RESISTANCE, REACTANCE AND THE CORRESPONDING PASSIVE ELEMENT.
1) Sketch the single phase equivalent circuit. Show all values 2) Calculate the total complex power absorbed by the wye connected load and the phase current , I CA
(i) Figure Q1 shown below presents a one-line diagran simple power system with two generators. Tabl¢ gives the corresponding line parameters. Form admittance matrix for the given system. Table Q1. Power line parameters Figure Q1. Power system
A voltmeter, ammeter, amd wattmeter are connected with suitable instrument transformers into a single-phase circuit as per figure, the following data was taken: current transformer ratio 5 to 1, potencial transformer ratio 20 to 1, voltmeter reading 100 V, ammeter reading 5 A, wattmeter reading 360 W find Power factor : a) 56%, b) 63.02%, c) 72%, d) none Power : a) 360 W, b) 3,600 W, C) 36,000 W, d) none
A 3-phase, star-connected alternator supplies a delta connectedload, each phase of which has a resistance of 15Ωand inductive reactance 20Ω. If the line voltage is 400V, calculate (a) the current supplied by the alternator and (b) the output power and kVA ratingof the alternator, neglecting any losses in the line between the alternator and the load.