The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at the receiving side (load side) is also 1 KV (Vr = 1 KV). Vr lags Vs by 300. The transmission line has an impedance of j97.5 ohms. The line drop would be: O A. 129.5 O B. 518 V O C. None of the choices are correct O D.O O E. 259 V

The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at the receiving side (load side) is also 1 KV (Vr = 1 KV). Vr lags Vs by 300. The transmission line has an impedance of j97.5 ohms. The line drop would be: O A. 129.5 O B. 518 V O C. None of the choices are correct O D.O O E. 259 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

The magnitudes of the open circuit and short circuit input impedances of transmission line are 100 ohm and 50 ohm respectively. What will be the characteristic impedance of the line?
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
Given a telephone transmission line of 100 mile long has Z,=685-j92Q, 0a=0.00497 neper/mile and f=0.0352 rad/mile work at 1000Hz. If Z=2000Q and Eg=10Vrms with Z:=700Q, find the sending end impedance, voltage, current, and power.
Design a quarter wave matching section if the line has a characteristic impedance of 100 ohm while the load Is a 300 ohm resistor. Specify the length of the matching section if the velocity factor is 0.90 at a frequency of 150 MHz.
transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the value of VSWR assuming that the line impedance is decreased by 30 % and load impedance is increased by 40%.
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the line, 988.1 A current is drawn under 400 kV interphase voltage. The angle of the current is -68. It is 6 degrees. With the short transmission line equations, the amplitude value of the phase neutral value of the busbar voltage to which the generator at the beginning of the line is connected is given correctly. A) 231.34 B) 52.35 C) 400 D) 380.28 E) 388.57
In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
The measurement made on a transmission line is given by the graphic in the figure. If the line length is 8.4 cm and characteristic impedance is 50 ohms; Find the load reflection coefficient, load impedance, reflection coefficient at the line input.
A high-voltage direct-current generating station delivers power to a city. The generator output voltage is V0 = 400 kV, the city is represented by resistance RL = 3918 ohms, and each wire of the transmission line round-trip between the station and city is represented by resistance RTL = 151 ohms. How much power (in mega watt) is lost along the transmission wire?
an overhead line is connected to a terminal apparatus through a length of single phase cable, the characteristics impedances being 400 and 50 ohms respectively. A traveling wave of vertical fromt and infinite tail of 100kv magnitudes originates in the overhead line and travels towards the junction with the cable during a period of 2us after the arrival of the wave at the junction. what voltage is reflected back into the line?
For a transmission line, the value of the open circuit and short circuit impedance are 100 ohm and 50 ohm respectively. What will be the value of the characteristic impedance of the line?