The voltage between two phases in a balanced three phase-system (4 conductors) is U = 660V.The voltage between the phase and the neutral is:a) V = 1143 Vb) V = 660 Vc) V = 381 VA resistance R-30 2 is connected in series with an inductance (L) of reactance X₁.-40 52 and a capacitor (C)reactance Xc-40 Q.The equivalent impedance (Z) is equal to:a) 70 2b) 30 (2c) 50 2The current absorbed by a resistive load of resistance 7.6 0, connected across the terminals of a battery ofelectromotive forceE = 14 V and internal resistance r=0.4 0, is:a) 1 = 1.75 Ab) I= 1.84 Ac) 1 = 35 A

Answered: Image /qna-images/answer/84da8122-5cdc-4809-8acc-7f84ce697711.jpg

Answered: The voltage between two phases in a…

The voltage between two phases in a balanced three phase-system (4 conductors) is U = 660V. The voltage between the phase and the neutral is: a) V=1143 V b) V = 660 V c) V = 381 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a star-connected load.The load is connected to a 260 V, three-phase,50 Hz supply and ABC phase rotation. Use Van as the reference. 1. Calculate the impedance of the load,( Zph) in each phase in polar form, the line current,( Ia) , line current,( Ib) in polar form, line current,( Ic) in polar form. Calculate the power factor,(pf) of the load and the total power absorbed,(P) of the load 2.Calculate the total apparent power absorbed,(S) of the load
Circuit elements with an inductance of 200 mH, a capacity of 50 μF and a resistance of 10 Ω are connected in parallel. If the average value of 198 V sinusoidal AC voltage is applied to this system, find the line current, impedance and phase angle of the circuit. (Take the frequency as 60 Hz.)
Question Vvv For the series- connected RC circuit, with an alternating current element E(t) = Eo sin wt inserted into it. Assume that the switch is closed at t = 0 and that at that time q(0) = 0 and i(0) =0. Use that Z² =R²+ (wC)- ², where Z is the steady state impedance of the circuit. Find i(t) for t> 0
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
1.1 We have two loads in delta and another in star in parallel, the impedances of the branches of the delta are equal and we have that RΔ=1p.u. and XΔ=0.75 p.u., while in the star we have equal values of the branches, but formed by admittances where we have the conductance in parallel GY=0.64 p.u. and inductive susceptance of BY=-j0.48 p.u. If the loads are being supplied by a positive sequence balanced three-phase source with line-to-line voltage of phases a and b of Vab=1∠ 30º, if the base values are line-to-line base voltage of 1kV and three-phase base power of 100kW. DetermineA) Line and phase voltages, line and phase currents of the load in delta, line and phase voltages of the star, line and phase currents of the star.B) Obtain separately the phasor diagram of the delta and star load with the values obtained in A), indicate on the scale that these are 1 p.u.=5cm for example.C) obtain the power triangle and the power factor separately for each load. D) Obtain the power…
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
Task A2 Power factor correction In an AC circuit, the current flowing through Load A is found to be 15<9.20 A. The voltage across the load is 240<620 V. 1) Calculate the apparent, real and reactive power, and the power factor of Load A. 2) A capacitor is connected in parallel with Load A to raise the load power factor to 0.98 lagging. Calculate the capacitance C of the capacitor to achieve the desired power factor. (< is the phase sign)
73. In phasor, the resistance has an angle of 90 degrees and the voltage and current are in phase." True False 74. The impedance (Z) of a circuit is the ratio of the phasor current to the phasor voltage. True False 75. Conductance is always expressed as a real number and comprised the real part of impedance equation. True False
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
An industrial load of200KW has a powerfactor of 0.5 lagging. Agroup of synchronousmotors operating at apower factor of 0.8leading is installed andthe over-all power factorimproves to 0.75 lagging.Determine the KVArating of the synchronousmotors installed.Answer = 130.2354 KVA
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…