The volumetric flow of water is 665.98 liters/min. Calculate the maximum length [m] of the pipe that can be used without cavitation? (NOTE: Take the water temperature 10 °C)

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Determine the direction of flow through the tube shown in Fig. 4, in which y 50 ib/ft', u = 0.40 p .…

A:

Q: Give the classification of flow meters

A: Flow meters can be classified into two categories - Mass flow meters Volume flow meters

Q: A 50 mm Venturi meter (C = 0.98) is installed in a 75 mm diameter horizontal pipe carrying oil…

A:

Q: Eight cubic feet of water flow per second downward through this pipe line. When the upper pressure…

A: Gauge pressure in section 1-1 = 20 lb/in2 Discharge = 8 ft3/s Find the reading of the lower gauge…

Q: Note: This page should be the first page of vour report Q1) Water flows from a large tank through a…

A:

Q: Oil of density ρ=880 kg / m3 flows through the Venturi tube (pictured). Calculate the flow if given:…

A: Given data: Oil density ρo=880kgm3 Mercury specific gravity sm=13.54 D=24 mm. d=12 mm. y=440 mm.

Q: Water flows in the smooth tubing shown. Calculate flowrate Q in L/s. Recall 1000 L = 1 m3. You may…

A:

Q: 1- Derive an expression for the flow rate q over the spillway shown in figure bellow per foot of…

A:

Q: A 250 mm diameter pipe carrying 30 l/s of water suddenly enlarges to 400 mm diameter

A:

Q: The SG of the oil in the tank is 0.93, and a plunger with a diameter of 5 inches is being pushed…

A: V1=0.5ft/s D1=5inch D2=30mm

Q: Water flows through the pipe system as shown, mass flowrate A divides equally into B and C, and…

A:

Q: anometer being used to indicate the pressure difference between two points in a fabricated system.…

A:

Q: the pipe is 2 feet lower than at point A. Draw a clear diagram of the pipe system that indicates the…

A: Solution is attached below

Q: Eight cubic feet of water flow per second downward through this pipe line. When the upper pressure…

A:

Q: A liquid of viscosity 5.2x10-5 Ibf-sec/ft² is flowing in a rectangular duct. The equation of the…

A: Stress is defined as the intensity of force acting over a unit area. Shear stress is the intensity…

Q: Qu: Water is flowing in pipeline shown in the figure; calculate the required dianeter (d), for the…

A: find the diameter ''d''.

Q: Nozzle of diameter 20 mm is fitted to a pipe of diameter 10 min find the force exerted on the water…

A: Given:d=20 mmD=10 mV1=1.2 m/min

Q: Water at 25°C is flowing in a 26 cm commercial steel pipe. The total length of the pipe is 1416m. If…

A:

Q: Water (at 20C) flows through a pipeline connected in series, as shown in the Figure. The…

A: Bernoulli's theorem Bernoulli's theorem says that total energy at inlet is equal to total energy at…

Q: A hose discharges water from a tank as shown. Find the rate of discharge and the pressure head at…

A:

Q: What is the pipe velocity at point 12 Given the specific gravity of pink liquid S=3.9 and height…

A: Given    Height, h = 0.4 m

Q: 33. If each nozzle delivers 0.1 gallon per minute in a 40-inch band, and the ground speed = 3 MPH,…

A:

Q: A pipe network consists of pipeline as shown. If the total rate of flow is 10 liters/sec, compute…

A:

Q: quid is flowing in a pipeline 60 mm in diameter at 8.25 m/hr. If the density of fluid 820 kg. per…

A:

Q: A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located…

A: To find : Calculate downward discharge of of water and also calculate velocity at the section 2…

Q: . A crude oil of viscosity 0.9 poise and sp. gr. 0.8 is flowing through a horizontal circular pipe…

A: Given: μ=0.9 poise=0.09 Ns/m2SG=0.8d=80 mm = 0.08 mL=15 mm=50 kgt=15 sec

Q: Salt water is flowing from point A to B (as shown in Figure: Q 3(b)) with 0.10 m/s. The pipe has the…

A:

Q: Water flows from section 1 to section 2 in the pipe shown in the figure. The total head loss from…

A: Given data: Diameter at section 1, d1 = 150 mm. Diameter at section 2, d2 = 50 mm. Pressure at…

Q: For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries…

A:

Q: A pipe with a radius of 9 mm is attached to a nozzle. If the velocity of flow in the pipe is 2 m/s,…

A:

Q: 2. Oil flows through the system shown in figure below with negligible losses. Determine the…

A: Given data

Q: A crude oil of viscosity 0.9 poise and relative density 0.9 is flowing through a horizontal pipe of…

A: Given:-D=120mmL=12mM=785 Nt=25 secμ=0.9 poiseρ=0.9To find:-Pressure difference, ∆P

Q: If pipe 1 diameter 30% of total discharge and pipe 3 diameter 60mm. What are the values of discharge…

A: We have given

Q: Water discharge flow rate of 0.001 m/s is delivered through the 30 mm cast iron pipe? €=0.15…

A:

Q: The diameter of a pipeline is 6-in at A and 18-in at B. A is 11 ft. lower than B. If the pressure at…

A:

Q: 6. A simple Pitot tube is used to measure the velocity V, as shown in the figure below. Determine…

A: Pitot tube is a mechanical device that is used for measure the velocity of flowing fluid at any…

Q: Using the figure depicted below, perform the following: (a) Calculate the minimum height h at which…

A:

Q: Show complete solution and formulas used. Show the schematic diagram too. Calculate the required…

A: Given: The water flow rate, Q = 30 US gallon/min The pressure above water level, P = 40 kPa The…

Q: Oil is flowing through the venture meter shown in the figure. The water velocity in the main pipe of…

A:

Q: Air flows thru a device shown in the figure below. If the flow rate is large enough, the pressure…

A:

Q: For the siphon shown in figure (2), calculate (a) The mass flow rate of water from the tank and (b)…

A:

Q: A jet of water with a diameter of 52 mm (d) hits a set of vanes, the absolute velocities are as…

A: Given that, Angle made by the absolute velocity at the inlet,  α=25° The angle made by the jet at…

Q: 71 For the system shown, What is the flow direction? What kind of machine is at A? Do you think both…

A: Solution is attached below:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.