The waveform displayed on an oscilloscope is as shown in Figure 3. The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 0.5 V/cm. Determine: (i) amplitude of waveform Q (ii) peak to peak value of waveform P (iii) frequency of waveform P (iv) angular frequency of waveform Q and (v) phase angle difference between P and Q in Degrees. 24°C Type here to search DOLI

The waveform displayed on an oscilloscope is as shown in Figure 3. The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 0.5 V/cm. Determine: (i) amplitude of waveform Q (ii) peak to peak value of waveform P (iii) frequency of waveform P (iv) angular frequency of waveform Q and (v) phase angle difference between P and Q in Degrees. 24°C Type here to search DOLI

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter9: Measuring Instruments

Section: Chapter Questions

Problem 10RQ: 10. What electrical quantity does the oscilloscope measure?

See similar textbooks

Similar questions

Please Connect the circuit shown above in Tinkercad and measure the output voltage in oscilloscope.
27) For the Double beam oscilloscope shown in Figure. Determine (i) the magnitude of pulse for waveform A and B, (ii) Time period of waveform A and B and (iii) Frequency of waveform A. The time/cm switch for waveform A is on 35 μs/cm, time/cm switch for waveform B is on 85μs/cm, the volts/cm switch for waveform A is on 35 V/cm and the volts/cm switch for waveform B is on 25 V/cm.
Given an oscilloscope input resistance (R2 in Figure 3 b) is 1MegΩ. Find the probe resistance (R1) so that the ratio of the source voltage (Vs) to the oscilloscope input voltage (Vin) is Vs/Vin = 10. R1=?
List the advantages, if any, in using the oscilloscope as an ac voltmeter.
The suitability of oscilloscopes for voltage measurement and DC display.
Ex. 1633. A 120VAC_RMS 60Hz line is connected to a Triac with a firing angles of 114 degrees and 294 degrees. What is the RMS voltage at the Triac output? This is the function of a modern dimmer switch. Hint: calculation can be simplified by considering only the first half of the sine wave. ans: 1
Mathematical Formula How Piezoelectric Energy is Obtained
QUESTION 2: What is the approximate voltage amplitude and frequency of the waveform below
Terms: amplitude (A), phase angle (ϕ), frequency (f), angular frequency (ω), period (T), peak value (Vp), peak-to-peak value (Vpp). Draw a 60 Hz, 5 Vp sine wave on a coordinate axis and graphically identify as many of the terms as possible from the previous section. Use voltage in volts for the y-axis, and time in milliseconds for the x-axis. You can use the blank OSC templates shown in the procedure section to draw the signals.
a) (i) Draw the electrical model of a piezoelectric crystal. (ii) Over what portionof the reactance curve do we desire oscillations to take place when the crystal isused as part of a sinusoidal oscillator? Explain. b) An N-channel JFET has IDSS = 16 mA and VP= -6 volts. Calculate the draincurrent and VDS (sat) when VGS = -4 volts.
The period of this signal is about ____ ms (milliseconds). Use this picture for 2 additional questions below. The oscilloscope range selector determines the scale on the screen. That means number of Volts per line for amplitude vertical (V/div) and the number of milliseconds per line for time horizontally (ms/div). The frequency of the signal in previous question is about ____ Hz. The peak to peak amplitude of the signal on the oscilloscope on first question is about ___ Volt(s). During sound digitizing the sound frequencies ranged from 200 Hz to 2.2 kHz. Based on Nyquist theorem the sampling frequency should be at least ____ Hz. Select the FM Radio Quality recording format on the picture below and calculate the size of a 30 seconds uncompressed audio file (like a WAV file) in kB (kilo Bytes). This is a ____ mega pixels picture. Based on the same image file properties screen shown in previous question, the size of…
John is measuring 2Vpp 1kHz waveform with settings of 500 mV/div and 100 ns/div. As it turns out, the oscilloscope displays waves similar to straight lines. What advice can be given to John so that the measurement results given are good and can be displayed on the oscilloscope?