The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 50 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (1) amplitude of waveform Q, (i) peak to peak value of waveform P, (111) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. 主 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P= (iii) Frequency of waveform P =

The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 50 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (1) amplitude of waveform Q, (i) peak to peak value of waveform P, (111) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. 主 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P= (iii) Frequency of waveform P =

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter9: Measuring Instruments

Section: Chapter Questions

Problem 10RQ: 10. What electrical quantity does the oscilloscope measure?

See similar textbooks

Similar questions

10. What electrical quantity does the oscilloscope measure?
Terms: amplitude (A), phase angle (ϕ), frequency (f), angular frequency (ω), period (T), peak value (Vp), peak-to-peak value (Vpp). Draw a 60 Hz, 5 Vp sine wave on a coordinate axis and graphically identify as many of the terms as possible from the previous section. Use voltage in volts for the y-axis, and time in milliseconds for the x-axis. You can use the blank OSC templates shown in the procedure section to draw the signals.
-) Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is 5 V / div, the CH2 probe voltage stage is 10 V / div and the time axis is 2ms / div. According to this information, a) What are the peak to peak and rms voltage values of the voltages in CHI and CH2? b) What is the frequency of the voltages in Hz? c) How many degrees is the phase difference between the two voltages, which voltage is leading?
The period of this signal is about ____ ms (milliseconds). Use this picture for 2 additional questions below. The oscilloscope range selector determines the scale on the screen. That means number of Volts per line for amplitude vertical (V/div) and the number of milliseconds per line for time horizontally (ms/div). The frequency of the signal in previous question is about ____ Hz. The peak to peak amplitude of the signal on the oscilloscope on first question is about ___ Volt(s). During sound digitizing the sound frequencies ranged from 200 Hz to 2.2 kHz. Based on Nyquist theorem the sampling frequency should be at least ____ Hz. Select the FM Radio Quality recording format on the picture below and calculate the size of a 30 seconds uncompressed audio file (like a WAV file) in kB (kilo Bytes). This is a ____ mega pixels picture. Based on the same image file properties screen shown in previous question, the size of…
Give the excitation table and transition table. State diagram too. K map too. Correct answer only
ii) Calculate the energy in the signal (shown in blue) over the period as shown (0 → 3 secs) in Figure 1b2) below:
Explain why voltage spikes and surges are high frequency occurences
Answer these two subparts 1. It is the ability of a material to generate an electric charge when subjected to pressure a. Piezo electric effect b. Varistor effect c. Optocoupling effect d. Statoring effect 2. it is passing electricity from an external source though piezoelectric crystals will convert the electrical energy into sound waves a. Piezoelectric effect b. Inverse piezoelectric effect c. Varistor effect d. Statoring effect
PEAK VALUE AND FREQUENCY ( NEED ONLY NEAT EXPLANATION HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
The voltage in your home is 120 Vac effective (rms), what is the peak value? Voltage specified as 100 Vac is understood to be what value? rms, peak or peak-to-peak? Convert 280V peak-to-peak, to its rms value. Assume a sine wave. What peak-to-peak value of ac sine wave would do the same work as 50 Vdc? Oscilloscope can display which value? (peak or rms)
Ex. 1633. A 120VAC_RMS 60Hz line is connected to a Triac with a firing angles of 114 degrees and 294 degrees. What is the RMS voltage at the Triac output? This is the function of a modern dimmer switch. Hint: calculation can be simplified by considering only the first half of the sine wave. ans: 1
24. The waveform displayed on an oscilloscope is as shown in Figure . Determine: (i) amplitude of waveform 'A' (ii) RMS value of waveform 'B' (iii) frequency of waveform 'A' and (iv) phase angle difference between 'A' and 'B' in Degrees.