The wooden section of the beam below is reinforced with two steel plates as shown. determine the moment maximum internal M that the beam can withstand if the allowable stresses for wood and steel are (σadm)wood = 6 MPa and ((σadm)steel = 150 MPa, respectively. Use E(wood) = 10 GPa and E(stell) = 200 GPa.

Q: 1. Two platoons of cars are timed over a distance of 0.7 km. Their flows are recorded. The first gro...

A:

Q: 3. A trapezoidal earth canal is to be designed to irrigate a 300-ha rice farm. The maximum water req...

A: Discharge=Area ×water requirement =300×10000×121000x24×60×60m3/s =0.42m3/s

Q: A circular island of 600 m radius has an effective rainfall of 5 mm/day. A central well 30 cm in dia...

A:

Q: Draw the shear and moment diagram of the beam shown below. w = 12 kips/ft. P= 20 kips hinge 10- 15'-

A:

Q: If pipe design diameter is equal 255 mm, Q =5500 m3/day, bed slope of 0.015 and n=0.015, then Qd/Qf ...

A: Given: The design diameter is 255 mm. The design discharge is 5500 m3/day. The bed slope is 0.015. T...

Q: An RCC beam is of size 230 mm x 500 mm overall depth and effective cover to compression steel and te...

A:

Q: Determine the force in member BF. The force is positive if in tension, negative if in compression. B...

A:

Q: Moment Distribution Method

A:

Q: SOLVE FOR THE MEMBER FORCE ON MEMBER CH. INDICATE THE UNITS & IF IN TENSION OR IN COMPRESSION.

A:

Q: Find the height that the buoy sink in salt water, in meters. * Find the maximum height, in meters, ...

A:

Q: A 100 mg of HNO, (strong acid) is added to water, bringing the final volume to 1.0 liter. Consider t...

A: Given data-100 mg of HNO3Final volume=1 literAtomic weights of H, N & O = 1 g/mol, 14 g/mol, 16 ...

Q: Write the shear and moment equations for the beam shown. Draw the shear and moment diagrams under th...

A:

Q: A particle starts from rest and travels along a straight line with acceleration a = (40 – 0.3v) m/s²...

A: Physics:  

Q: lo kJ Determine (approximately) the reactions at the base of the columns of the frame shown. Use the...

A:

Q: Problem 3. Determine the magnitude of force in members BC, BE and DE of the truss shown and state if...

A: The answers are found to be  Forces in member 1. BC=5250 lb (Tension) 2. BE=3750 lb (compression) 3....

Q: Analyze the frame using Moment Distribution Method. Draw Shear and Moment Diagrams. 15 kN 15 kN 2m 1...

A:

Q: 0-42. Determine the horizontal deflection at C. Use the method of virtual work. Assume the members a...

A: CALCULATIONS of horizontal deflection at C using Unit load method## #  

Q: From the given figure below and its properties, calculate the stress at the bottom where at the fixe...

A: calculate moment at fixed end and use stress equations.

Q: 120 kN/m В 80 kN/m 5 m 3 m - For the beam shown in the figure, determine the magnitude of the maximu...

A:

Q: Compute the design moment strength of the section shown below if f. = 40 MPa and f, = 500 MPa. - 300...

A: Given   Doubly reinforced beam Calculate ultimate moment

Q: 1. Complete the given table Sieve number Diameter(mm) Mass retained Cumulative Mass Percent Passing ...

A:

Q: Use virtual work method. AE constant. Solve for vertical displacement at joint C in terms of AE. Ind...

A:

Q: A differential levelling was conducted from BM1 to BM2 30 km apart. BM1 is at elevation 124. 08 m. T...

A:

Q: A theme park has a single entrance gate where visitors must stop and pay for parking. The average ar...

A:

Q: At an impaired driver checkpoint, the time required to conduct the impairment test varies (according...

A: Given Data, Average Flow rate arriving = 30 vehicle/hr Average time spend on test = 60 seconds

Q: A vertical sag parabolic curve has a length of curve of 420 m. from A to B. The back tangent has a s...

A: We have to determine the value of elevation of point A as per the given data in the question like gr...

Q: 1.3.5 Problems 1. Evaluate u v where u = e, +3e, - 2e,, v = 4e,- 2e, +4e,.

A:

Q: Determine the reactions at A and B for the beam with the overhang as shown. 10 kip 1.5 kip/ft Free e...

A: Given data : Point load P=10 kip Uniformly distributed load q=1.5 kip/ft   To find : support reactio...

Q: Determine the force in each member of the loaded truss using the method of joints. C D 2 m 2 m E 2 m...

A: We have to determine the force in each member of the loaded truss using the method of joint as per t...

Q: Ib = 500- ft W. max A 6 ft >+ 6 ft → E 6 ft B

A: As per rules i will give only one answer. So that shear diagram is given below.

Q: 3. Solve the a) slope at C and b) deflection at B using either AMM or DIM. Use of direct formulas no...

A:

Q: Situation 3: A staggered bolted connection is shown in the figure. The plates are 12 mm thick and 40...

A: We will use basic formula

Q: A slender homogenous wire of uniform cross section is bent into the form shown. Determine the positi...

A:

Q: Explain the 5 Different Design Concepts (balance, focal point, rhythm, unity, details) in Interior D...

A:  5 Different Design Concepts (balance, focal point, rhythm, unity, details) in Interior Design:

Q: F1 lb F2 Ib/ft F3 Ib/ft A BỊ DI E 3 ft 6 ft 9 ft 3 ft 9 ft

A:

Q: A forward tangent having a slope of -4% intersects the back tangent having a slope +7% at point V at...

A:

Q: Compute the width of the base.

A:

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b) Suctio...

A: Solution- The given values are as follows,Pump performance graph,The Specific speed & suction sp...

Q: For this soil, LL=23 and Pl=19, classify the soil by using a. AASHTO b. USCS c. Give group name and ...

A: Given that for an inorganic soil, the grain size distribution as,  Also, LL=23 and PI=19 The soil h...

Q: Calculate the support and internal hinge reactions for the beam shown below. Show your complete solu...

A: We are required to find the support and internal hinge reactions 

Q: 1200 lb 600 lb/ft B A D -2 ft→+2 ft→ -4 ft- 500 lb Shear Equation Moment Equation egment AB egment B...

A:

Q: Problem1.A 500 m2 botanical garden which harvest 1000 flowers per day of 15 variations, in a year th...

A: Given, The area of botanical garden A is 500 m2. Depth of rainfall=170 cm/yr  

Q: According to the truss shown in figure, The force in member CH (FCH) in KN is (T: Tension and C: Com...

A: To find force in member CH

Q: 0.4 m A B

A: Given : acceleration of block B = 0.2 m/s2

Q: A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement ar...

A:

Q: An aircraft manufacturer uses 1,000,000 special rivets per year at a uniform rate. The rivets are ma...

A:

Q: A rectangular beam, which length from the compression fiber to the neutral axis is equal to 340 mm. ...

A:

Q: A chain was used to check the distance between two control points on a large building project. The d...

A:

Q: From station A (35 + 220) with center height of 4.5 m in cut, the grade of the ground surface is −6%...

A:

Q: A beam, which is rectangular, has a base of 250 mm, and d = 575 mm. The beam is singly reinforced, w...

A: Using limit state method Strain in concrete 0.003 Strain in steel 0.005 Depth 575 mm Width 250mm Bal...

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.