There are four stations in a process: Station-1, Station-2, Station-3, and Station-4. They process a single product. The flow of the accepted and rejected products are shown in the process flow chart. The total volume of production is 105 products per hour. 23% of the products of Station-1 need repair and are directed to Station-3 for repair, the rest are sent to Station-2. 15% of the products of Station-2 need repair and are directed to Station- 3 for repair, the rest are sent to Station-4. 12% of the incoming products of Station- 3 are rejected, are sold at a low price, and leave the process. The rest go to Station-4. All the products of Station-4 are good, no need to repair, and no rejection. On average there are 8, 2, 40, and 5 products in Stations 1, 2, 3, 4, respectively. Compute the average flow time in this process. Enter your answer in MINUTES with ONE DECIMAL point.

There are four stations in a process: Station-1, Station-2, Station-3, and Station-4. They process a single product. The flow of the accepted and rejected products are shown in the process flow chart. The total volume of production is 105 products per hour. 23% of the products of Station-1 need repair and are directed to Station-3 for repair, the rest are sent to Station-2. 15% of the products of Station-2 need repair and are directed to Station- 3 for repair, the rest are sent to Station-4. 12% of the incoming products of Station- 3 are rejected, are sold at a low price, and leave the process. The rest go to Station-4. All the products of Station-4 are good, no need to repair, and no rejection. On average there are 8, 2, 40, and 5 products in Stations 1, 2, 3, 4, respectively. Compute the average flow time in this process. Enter your answer in MINUTES with ONE DECIMAL point.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

3.Consider the following three-stage production process of glass ceramics. The process is experiencing severe quality problems related to insufficiently trained workers. Specifically, 20 percent of the parts going through operation 1 are badly processed by the operator. Rather than scrapping the unit, it is moved to a highly skilled rework operator, who can correct the mistake and finish up the unit completely within 15 minutes. The same problem occurs at station 2, where 10 percent of the parts are badly processed, requiring 10 minutes of rework. Station 3 also has a 10 percent ratio of badly processed parts, each of them requiring 5 minutes by the rework operator. a)What is the utilization of station 2 if work is released into the process at a rate of 5 units per hour? b)Where in the process is the bottleneck? Why? (Remember, the bottleneck is the resource with the lowest capacity, independent of demand.)
Which of the following is a typical characteristic a service process? Group of answer choices a Low customer contact b Perishable outputs c Tangible output d Low labor requirements e High levels of inventory f All of the above
The analysis of flow process maps encourages 6 things. Name them.
A process has seven elements composed of combination of worker and machine. Elements A, B, D, and F are worker-controlled while elements C and E are machine controlled. Element G is a worker-controlled irregular element performed every five cycles Machines are idle during elements A, D, and G. Two units are produced every cycle. Below are the observed time (in minutes) and performance rating of each element. Work Element Observed Time (in minutes) Performance Rating A 0.75 115% B 1.20 120% C 1.40 N.A. D 1.05 90% E 1.25 N.A. F 1.20 105% G 1.60 85% Worker's allowance is 20% a) Determine Normal Time . Answer in 4 decimal placesb) What is the standard time? Round up answer in 2 decimal places.c) If the worker's performance during actual production is 125% on all manual elements for seven hours worked on an eight-hour shift, how many units will be produced? Round up answer in integer value.d) Determine the worker's efficiency (in percentage). Answer in 2 decimal places
A two station nurses clinic operates where you must visit the first station before the second. The CV of a cycle time for this is .75. Average process time for the first nurses station is 15 minutes. Average process time for the second nurses station is 9 minutes. a. Find the standard deviation of the overall cycle time b. Assume the std dev of the first nurses station is to be twice that of the second. What would the new coefficient of variation be if the standard deviation of the second nurse station is reduced by 60%?
Mr. Aris Benn manages an assembly line that produces a piece of equipment that is used to clean floors. The process to produce this piece of equipment consists of 10 steps. 2. Using this example, demonstrate how to balance the line and how to calculate its efficiency.
Describe four potential problems that might develop when operating a large number of processes at the same time.
Maxine has identified the following process times and desired output. What is the theoretical minimum number of work stations? What is the Efficiency and Balance Delay for this process? mix dough 90 sec desired output 30 batches/hour shape cookie 50 sec cook 45 sec cool 75 sec Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.
. A small, privately owned Asian company is producing a private-label soft drink calledYoggo. A bottling line puts the soft drinks into plastic bottles and then packagesthe bottles into boxes holding 10 bottles each. The bottling line is comprised of thefollowing four steps: (1) the bottling machine takes 1 second to fill a bottle, (2) the lidmachine takes 3 seconds to cover the bottle with a lid, (3) a labeling machine takes3 seconds per bottle, and (4) the packaging machine takes 4 seconds to place a bottleinto a box. When a box has been filled with 10 bottles, a worker tending the packagingmachine removes the filled box and replaces it with an empty box. Assume that thetime for the worker to remove a filled box and replace it with an empty box is negligibleand hence does not affect the capacity of the line. Problem data are summarized in thefollowing table. a. Draw a process flow diagram of this process. b. What is the capacity (bottles/hour) at the resource “Apply a lid”? c. What…
Charles Lackey operates a bakery in Idaho Falls, Idaho. Because of its excellent product and excellent location, demand has increased by 25% in the last year. On far too many occasions, customers have not been able to purchase the bread of their choice. Because of this size of the store, no new ovens can be added. At a staff meeting, one employee suggested ways to load the ovens differently so that more loaves of bread can be baked at one time. This new process will requrie that the ovens be, loaded by hand, requiring additional manpower. This is the only production change that will be made in order to meet the increased demand. The bakery currently makes 1,600 loaves per month. Employees are paid $8 per hour. In addition to the labor cost, Charles also has a constant utility cost per month of $700 and a per loaf ingredient cost of $0.50. Current multifactor productivity for 640 work hours per month= .242 loaves/dollar (round your response to three decimal places). After increasing…
A process of making chair is described as follows: Stage 1 Seat and back attached Stage 2 Legs attached The production speeds are 15 chairs per hour for Stage 1 and 30 chairs per hour for stage 2. The cycle time of the process is ______minutes. The flow time of the process is ______ minutes.
Mr. Aris Benn manages an assembly line that produces a piece of equipment that is used to clean floors. The process to produce this piece of equipment consists of 10 steps. 1. set up a numerical example of the line balancing problem at hand.