There are many applications for an RLc circuit, including band-pass filters, band-reject filters, and low-/high-pass filters. Series and parallel RLC circuits can be used to create band-pass and band-reject filters. For example, Figure 2 shows the RLC circuit of a band-pass filter. Find the transfer function Ir(j@)/I<(j@) for the circuit. ir(1) ) (1 R i:(1) L Figure 2 [Rajah 2]

There are many applications for an RLc circuit, including band-pass filters, band-reject filters, and low-/high-pass filters. Series and parallel RLC circuits can be used to create band-pass and band-reject filters. For example, Figure 2 shows the RLC circuit of a band-pass filter. Find the transfer function Ir(j@)/I<(j@) for the circuit. ir(1) ) (1 R i:(1) L Figure 2 [Rajah 2]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q6 Make a sketch of an RL circuit. Develop the differential equation for the circuit. Find the transfer function relating the output voltage across the inductor to the input voltage. Based on your transfer function determine the type of filter represented. Make an appropriate sketch and classify as low /high pass filter
Design a low-pass filter with 3-dB frequency, fC = 10 kHz. Use either a simple RL or a simple RC circuit. (Note: Consider what values of inductors and capacitors are available in a college lab.)
Model a human ear as a low pass filter, then assume R = 1 KQ and C = 1µF, then create an excel sheet to study the relationship between ( VOutput/ Vinput) versus the frequency. Put frequency in steps of 100. then draw the relationship between (VOutput/ Vinput) in y axis and frequency in x axis. From your graph find the frequency that the human body will not be able to hear (assume this will happen at (VOutput/ Vinput ) = 0.1)
Part (a): Using the following components, design and successfully run a basic Band pass filter. (Please include the design of the circuit in your answer. I've already had one incomplete solution.) Your cut-off frequencies should be 0.5 and 40Hz. Provide screen shots of all 3 waveforms, i.e. Low Pass, Hi Pass and unattenuated wave form in the pass band range. LM741 op amp 2 x 0.1 uF capacitors 2.3MΩ resistor 4.5 MΩ resistor 2 x 27kΩ resistors 0.1 uF capacitor 0.2uF capacitor
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
The transfer function of a first order RC high-pass filter is given below: Draw the circuit representing a RC first [1] order high-pass filter. Clearly show the input and output on the circuit. Proof that the half-power break-frequency of the filter can be described by the equation below (show all steps): fB= 1/2(pi)(R)(C)
Passive filters are made of passive components, tuned to the harmonic frequencies that are to be attenuated. Show that a series LR circuit is a lowpass filter if the output is taken across the resistor.
2) You are asked to design a DSB-SC modulator to generate a modulated signal km(t) cos wc t, where m(t) is a signal band-limited to B Hz. Figure below shows a DSB-SC modulator available in the stock room. The carrier generator available generates not cos wc t, but cos3 wc t. M(f) km(t)cos³ w̟t m(t) A Filter b f -B В cos wct a) Sketch the signal spectra at points a and b.(a:1,b:8) b) Is it possible to realize a DSB-SC modulator as in the figure above? (If yes) what kind of filter should be used? Comment on the bandwidth of the filter and the minimum and/or maximum frequencies that the filter should allow to pass. c) What is the minimum usable value of wc?
I need some help. I am designing a bandpass filter with fl=3400 Hz and fh= 7500 Hz. Based on that I need the values for the RCL circuit, assuming that the capacitor is 1 microfarat. So, I need some help in calculate the center frequency, bandwith, Q, center frequency as well. I need clear steps and calculations. Any help will be appretiated.
4. An engineer needs to design a capacitive filter that will attenuate frequencies greater than the cutoff frequency; answer the following questions based on this design: a. Illustrate the filter that the engineer will need b. Determine H, for that design C. Plot the magnitude response for that filter
Please provide Handwritten answer. Electrical Engineering It is a common practice to low-pass filter signals before feeding them into an A/D Converter. The purpose of this filter is to eliminate any noise or other frequency components beyond a useful frequency range. For instance, if you are recording ECG, you would low-pass filter it at 100Hz because there is no useful frequency components beyond 100Hz and if there is any component that would be noise. What problem arises during sampling of the signal by the A/D Converter if this pre-filter is not used? How does the sampling frequency need to be adjusted with and without the pre-filter? Answer the question considering Nyquist theorem.
Vout H(f) = 1+j in fB