THERMODYNAMICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWERS. PLEASE ANSWER ALL Two Carnot heat engines operate in series. The first heat engine absorbs heat of 100kW at 400°C while second heat engine rejects heat at 100°C. If the efficiencies of the heat engines are the same, a. Draw the schematic diagram of the system b. Find the intermediate temperature in between the heat engines c. Heat rejected for both heat engines

Q: A projectile is launched from point A with speed vo= 20 m/s. Determine the value of the launch angle…

A: Given Velocity at point A is v = 20 m/s let us take acceleration due to gravity g = 9.8 m/s2 we know…

Q: The swing door is held in the position shown in the figure, by means of two cables AB and AC and,…

A: Here, A(2,0,4) B(5, 3cos20, 3sin20) =B(5,2.819,1.026) C(0, 3cos20, 3sin20) =C(0,2.819,1.026) Now,…

Q: Three equations of equilibrium are available to determine the unkowns. -Two dimensional force…

A: Three equation of equilibrium consist of the balance of forces in two dimensional and moment balance…

Q: As depicted, a column is contained by a rigid material on its x-axis and has initial dimensions of…

A:

Q: A CARNOT heat engine receives heat from a reservoir at 900°C at a rate of 800kJ/min and rejects the…

A:

Q: 4. Consider the branched pipe flow shown below used to transport water. equipped with pressure…

A: Given data as per question Total volumetric flow rate at the inlet (1), Q= 0.27 m3/s d1=12.5…

Q: The pins on the frame at B and C each have a diameter of 0.25 in. If those pins are subjected to…

A:

Q: 4. A 10 lbm is drop on a 5 kgm piston with a face area of 800 cm² causing the cylinder to decrease…

A: Given: Let us consider the given data, Dropped ball's mass, mb=10 lbm= 4.53 kg Pistons mass, mp=5 kg…

Q: 2.8 CALC A bird is flying due east. Its distance from a tall build- ing is given by x(t) = 28.0 m +…

A:

Q: 5. A manometer with arms of unequal diameters have cross sectional areas of 10 cm² and 5 cm²,…

A:

Q: In the figure shown, mass m1=78 kg and the mass of the angle bracket is 50kg/m. Determine the…

A:

Q: A turning operation is carried out on aluminum. Based on the specific energy values in the table in…

A:

Q: ble containing the ideal gas specific heats of various common gases. diffe Uko K

A: Given data as per question P1=150 kPa, T1=39°C P2=150 kPa, T2=337°C

Q: 11 Calculate the work done in blowing a soap bubble of diameter 100 mm. Assume the surface tension…

A: surface tension S=0.038 N/m Diameter D=100mm=0.1m have to calculate work done

Q: The 80mm diameter shaft is made of 6061-T6 aluminum allow and subjected to the torsional loading…

A:

Q: The method of locating the center of gravity of a mass or an area is based on the method of…

A:

Q: y h с b bh .1

A:

Q: Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater and one…

A: Given: To find:

Q: 3 decimal places Convert specific heat 0.53 BTU/lb-F to kJ/kg-K

A:

Q: (1-C.s) m/s² where Cis a consta Q13. The acceleration of a particle traveling along a straight line…

A: Givena=1-Cs      m/s2c=0.1vo=0so=1.7mt=0v=? when s=4.8m

Q: The disk has an angular acceleration a = 7 rad/s² and angular velocity w = 3 rad/s at the instant…

A: Givenα=7 rad/s2ω=3 rad/s

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: The figure shows a 5.50 kg block on a ramp. The block is also attached to a massless spring with…

A:

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Problem 4 If a 5-kg steel plate is attached to one end of a 0.1 m x 0.3 x 1.20 m wooden pole, what…

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 131 feet and explode…

A: Before wind was blowing Height of intersection y=131 ft Max height H=131+30  H=161 ft we get…

Q: A manufacturer conducted an experiment for an evaporator capacity 500 kW cooling and designed for…

A: Given Data: Evaporator Capacity QC=500 kW COP of absorption refrigeration system COP=2 Evaporator…

Q: A door of rectangular shape is hinged along the axis whose direction lies in the xz plane. The door…

A: Write the given data. F=100 N Write the vector CD. CD=-2i+j+2k

Q: In a single pass rolling process using 410 mm diameter steel rollers, a strip width 140 mm and…

A: Given data:diameter of steel roller, d=410 mmwidth of the strip, w=140 mmthickness of strip, t=8 mm

Q: A single-stage rocket is launched vertically from rest, and its thrust is programmed to give the…

A:

Q: Required information Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant…

A:

Q: The 16-kg block A and the 21-kg cylinder B are connected by a light cable that passes over the 4-kg…

A:

Q: A particle is launched from point A with a horizontal speed u and subsequently passes through a…

A:

Q: At a construction site, a 60.0 kg bucket of concrete hangs from a light (but strong) cable that…

A: Given data: M=60 kgm1=80 kgm2=50 kg Need to determine the speed speed of the bucket after descended…

Q: 20 The efficiency n of a fan depends on the density p, the dynamic viscosity of the fluid, the…

A:

Q: A 0.03-1b bullet traveling at 1300 ft/s strikes the 10.8-lb wooden block and exits the other side at…

A: Given that: Initial velocity of the bullet is 1300 ft/s Final velocity of the bullet is 50 ft/s (a)…

Q: Assume the input power to a pump P (ML T-¹) is depend on Q- Flowrate (L³ T-¹), H-pump head (L),…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: # of teeth input gear = 20 # of teeth output gear = 80 What is the gear ratio (in lowest terms)?

A:

Q: 17 When a pressure of 20.7 MN/m² is applied to 100 litres of a liquid its volume decreases by 1…

A: as per guideline i have to solve only first part of your question ,please repost left one.

Q: Indicate how velocity, water temperature, and pipe area affect the Reynolds number.

A: Viscosity: The measure of the resistance to fluid flow (continuous shear deformation) is known as…

Q: Water is the working fluid in a reheat-regenerative Rankine cycle with one closed feedwater heater…

A: Given data: For a reheat regenerative rankine cycle P1=P10=P111400 lbf/in2, T1=1000oFP2=P4=500…

Q: A particle moving in the x-y plane has a velocity v = 8.58i + 2.14j m/s at a certain instant. If the…

A:

Q: Situation 2. Determine the member forces BD, CD, and CE using Method of Section. Indicate if (T) or…

A:

Q: An aircraft performs a maneuver called an "aileron roll." During this maneuver, the plane turns like…

A:

Q: A truck with mass of M is going to tow the car with mass m. For values of M and m please follow the…

A: Mass of the truck→M=150000g Mass of the car→m=800g Initially the truck is moving with 130 Km/h speed…

Q: A 1250kg beam is attached to a building and supported by a cable that makes an angle of 30 degrees…

A: Subject: Solid Mechanics

Q: A car starts from rest with an acceleration of 5.0 m/s² which decreases linearly with time to zero…

A: Given:Initial Acceleration, a1=5.0 m/s2Acceleration after t=11.2 seconds, a2=0Find:The time required…

Q: A projectile is launched from point A with speed vo = 34 m/s. Determine the value of the launch…

A: For the given projectile motion, initial velocity is 34 m/s. It is required to determine the launch…

Q: 3. A water jet pump has an area A;= 50 cm² and a jet velocity v₁ = 25 m/s, which entrains a…

A:

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

A: Given: P1 = 2 KN P2 = 1.5 KN To find: FCD and FGF