THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.

THIN WALLED PRESSURE VESSELS SITUATION: A cylindrical water tank is 8 m in diameter and 12 m long. The material stress is limited to 40 MPa. If the tank is to be completely filled determine the following: 3. Thickness of the tank plating in mm if subjected to longitudinal stress 4. Thickness of the tank plating in mm if subjected to circumferential stress. 5. Minimum required thickness to be purchased if the material is sold in 2mm increments.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem : Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hooke's Law (E) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters?b) Check whether the pressure vessel is safe or not? Given data: - The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal stress is σL = 200 MPa.Hooke's Law (E) = 150 MPaThe radial stress is σR = -50 MPa.
Medium oil having a sp.gr. of 0.90 flows through a 120 mm diameter pipe with a mean velocity of 5.3 m/s and friction factor of 0.01. Oil has an absolute viscosity of 0.04 Pa.s. Compute the shear stress at the wall of the pipe.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion? Given data: -The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal Stress is σL = 200 MPa.Hoop Stress σθ = 150 MPaThe Radial Stress is σR = -50 MPa.
Medium oil having a sp.gr. of 0.90 flows through a 120 mm diameter pipe with a mean velocity of 5.3 m/s and friction factor of 0.01. Oil has an absolute viscosity of 0.04 Pa.s. Compute the shear stress at the wall of the pipe. a. 31.601 b. 60.131 c. 13.160 d. 61.310
A thick cylinder 1 meter inside diameter and 7m long is subjectedto an internal fluid pressure of 40MPa. Determine the thickness of the cylinder ifthe maximum shear stress in the cylinder is not to exceed 65MPa. What will be theincrease in the volume of the cylinder? E=200GPa, μ= 0.30.
For the same condition as the previous problem (After a solid block is put on a scale in the water tank as shown in the picture, the total water volume level increases from 5.0 m3 to 6.0 m3. The reading from the upper spring scale is 36.9 kN, and the reading from the scale in the water is 30 kN. The specific weight of water is γw=9.81kN/m3. ), select the correct equilibrium equation alone the vertical direction:______ A. Fb + Fspring=w B. Fb+Fspring-Fscale=w C. Fb+Fspring+Fscale=w D. Fb-Fspring-Fscale=w
Oil (µ = 0.35 Pa-sec) flows through a horizontal 20 cm diameter circular pipe. The velocity at any point in the pipe’s cross-section a distance at a distance y from the center is: V =64(r² − y²) / μ where: r = 10 cm (radius of the pipe) Determine the following: a) Maximum flow velocity (m/sec) b) Shear stress (Pa) at the pipe’s centerline c) Shear stress (Pa) at the pipewalls?
Make your solution organised and state assumptions. A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to?A. 2725 B. 1090. C. 545 D. 110 E. NOTA
A steel pressure vessel (_y = 250 MPa, E = 200 GPa) has a length of 4 m and a diameter of 1.2 m (cylindrical). It is designed to hold natural gas at a pressure of 6 MPa. Calculate the wall thickness required to safely contain flammable gases, taking into account a safety factor of 5.0 to prevent failure. Use the "maximum principal stress" criterion. Next, calculate the Von Mises stress corresponding to the stress state of the reservoir. Enter your numerical answer. Please include free body diagrams and possible steps
Compute the head loss (in meters) in 2000 m of horizontal, steel pipe with nominal pipe size of 300 mm and SCH 30. The pipe is carrying water with an average velocity of 1.88 m/s. Take water at 20°C to have a viscosity of 1.00E-3 Pa-s and density of 1000 kg/(m^3). Take the roughness of steel pipe to be 0.048 mm. Round your answer to 2 decimal places.
A cylindrical tank has an inside diameter of 5 inches and is subjected to an internal pressure of 500 psi. If maximum stress is 1,200 psi, determine the required thickness. A. 1.195 in C. 1.395 in. B. 1.595 in. D. 1.795 in
Water flows through a 600 mm diameter pipe with a velocity of 2.7 m/s. Bulk modulus of water is 2060 MPa and the pipe has modulus of elasticity of 200 GPa. The pipe has thickness of 18 mm. Compute the speed of pressure wave.