Three friends decided to connect their individual car batteries in parallel using ideal cables (negligible resistance) to power up the car of their fourth stranded friend as shown in this circuit. Unknown to them, their batteries are not fully charged and have different series resistance values and voltages as indicated. The starter motor of the fourth friend's car has an effective resistance of 0.185 ohms. 0.025 gho 0.020 ohm 12 V +11.2V 0.030 obro 0.050 ohm + 11.8 V +10.0 V MRm = 0.18502

Three friends decided to connect their individual car batteries in parallel using ideal cables (negligible resistance) to power up the car of their fourth stranded friend as shown in this circuit. Unknown to them, their batteries are not fully charged and have different series resistance values and voltages as indicated. The starter motor of the fourth friend's car has an effective resistance of 0.185 ohms. 0.025 gho 0.020 ohm 12 V +11.2V 0.030 obro 0.050 ohm + 11.8 V +10.0 V MRm = 0.18502

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter2: Electrical Quantities And Ohm’s Law

Section: Chapter Questions

Problem 3PA: You are an electrician installing the wiring in a new home. The homeowner desires that a ceiling fan...

See similar textbooks

Similar questions

Q: A wood panel containing 16 solar cells. Calculate the total open circuit voltage and short circuit current coming out of the board and draw the relationship between current and voltages in the following cases 1- If you connect each two cells in series and connect the groups in parallel. 2- If all four cells are connected in parallel and the groups are linked in succession, noting that each cell has the following characteristics: Vos = 0.75V, Isc = 2 mA
The values of the circuit elements are given below. accordingly, find the current i at t=34.6 sec.
Given that the total resistance is 15 Ohms and the Voltage Source is 30 V: (1) Determine the current through the 18W resistance of the circuit.(2) Potential difference across the 10W resistance if a 30Vdc source is connected across the terminals.
Using Equivalent Resistance Formula/Computation find: RBE Set the supply voltage to 5VDC. Get the ratio of the supply voltage and total current (R=V/I). Show complete solutions. Answers must be at fourth decimal place.
Using Circuit Analysis answer the ff. 1. If R = 1kohm, what is the equivalent resistance (in kohm) seen from the source? Note: Do not round-off intermediate answers; express the final answer in three decimal places. 2.If v_s is 21 V, what is the power (in mW) delivered by this source? Note: Do not round-off intermediate answers; express the final answer in two decimal places.
Solve For Current in 15 Ohm resitance using any theorem Thankyou!
Complete Solutions 1. A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.2. A 45-ohm resistor is connected in series with a resistor R whose ohmic value isunknown. If the total current (taken by both resistors) is 7-amperes and thesupply voltage is 120-volts. Calculate the resistance R of the unknown.
Experiment No. 02: Equivalent Resistance of Series, Parallel and Series Parallel Circuits.
Four resistors of 2ohm, 3ohm, 4ohm, and 5ohm, respectively are connected in the parallel, what potential difference must be applied to the group in order that tatol power of 100 watt may be observed.
Analyze the circuit of the figure shown to determine the voltages at all nodes and the currents through all branches. Where β=30, ?????? =0.2 V, ??? = 0.7 V and assume thetransistor is silicon.
This is about Pavegen Floor Tiles. The Pavegen tile has 5 watts per step. Assume that there is 15 steps per minutes in peak hour. The battery banking is 48V, 600ah, a. How many pavegen tiles to be connected to charge the battery banking? b. How the tiles are connected? Is it Series or Parallel. (computation) I need expert to help me this thanks.
When a voltage of 100V at 50Hz is applied to a choking a coil A, the current taken is 8A and the power is 120W, when applied to a coil B, the current is 10A and the power is 120W. what power will be is 10A and the power is 120W. what power will be taken when 100V is applied to the two coils connected in series?