Three pipes steadily deliver water at 20°C to a large exit pipc in Figure 1. The velocity V;= 5 m's, and the exit flow rate Q,= 120 m’/h. Find (a) V;; (b) V;; and (c) V, if it is knownthat increasing Q, by 20% would increase Q., by 10%.D, 6 cmD; = 5 cmD =9 cmD = 4 cm

Given data, Q4 = 120 m³/s V2 = 5 m/s To find out the V1, V3 and V4

Three pipes steadily deliver water at 20°C to a large exit pipe in Figure 1. The velocity V; = 5 m's, and the exit flow rate Q, = 120 m'/h. Find (a) Vi; (b) V; and (c) V, if it is known that increasing Q, by 20% would increase Q. by 10%. D, =6 cm D; = 5 cm D, = 9 cm D = 4 cm

Three pipes steadily deliver water at 20°C to a large exit pipe in Figure 1. The velocity V; = 5 m's, and the exit flow rate Q, = 120 m'/h. Find (a) Vi; (b) V; and (c) V, if it is known that increasing Q, by 20% would increase Q. by 10%. D, =6 cm D; = 5 cm D, = 9 cm D = 4 cm

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Related questions

Q: A framed of 6 m span is carrying a central load of 10 kN as shown in Fig. 13.17. 10 kN 3 m 3 m 6 m F...

Q: NEED WITHIN 1HR PLS THANKS Provide a formula for finding the shear force and bending moment at midsp...

Q: 5. In a deep saline water aquifer, there is a zone of fresh water of 100 ft depth. A well is drilled...

A: Given data Depth of saline water = 100 ft Depth of well = 80 ft Discharge from well = 0.5 cfs Per...

Q: A column is subjected to a load through a bracket as shown in the figure. 15 cm P = 10 kN %3D 10 cm ...

Q: Determine the moment of inertia with respect to the x'-axis (Ix') 150 mm y 30 mm X' 200 mm 20° 30 mm...

Q: The box slides down the slope described by the equation y = (0.05x²) m, where x is in meters. If v, ...

Q: In a drained tri-axial compression test, a sample of sand fails at deviator stress of 150 kPa under ...

A: confining pressure; σ3 = 50 kPa Deviator Stress; ∆σ = 150 kPa Now, we Know. Pressure applied; σ1 = ...

Q: Use the moment area method and determine the slope just to the left and just to the right of the pin...

A: Given -

Q: A column is subjected to a load through a bracket as shown in the figure. 15 cm- P= 10 kN %3D 10 cm ...

Q: y 9 kips/ft 5 kips/ft A В C D 6 ft 10 ft 11 ft

Q: 0.6 m 30 45°

Q: Y1 V2

Q: . It describes motion that is not constant through time. Rectilinear Motion Curvilinear Motion Conti...

A: Erratic motion Erratic motion is not constant throughout the time.

Q: No. 3. The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an ...

A: Given data: E1=200 GPaE2=70 GPaE3=70 GPa

Q: Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa ЗHD25 f, = 420 MPa A, = 2457 mm² 65...

A: Given data, fc = 30 MPa Fy = 420 Mpa As = 2457 mm² To find out the maximum UDL.

Q: Determine the expressions of V and M and draw the shear force and bending moment diagram for the bea...

Q: A cube (40 mm) is resting on ground and all vertical faces are equally inclined to the vertical plan...

A: given cube -400mm

Q: The sieve analysis of ten soils and the liquid and plastic limits of the fraction passing through th...

A: Reference : AASHTO Classification system. From given data ; % passing No 200 : 8 , which is less tha...

Q: 600 CA

Q: magnitude and direction of the resultant.

A: GIVEN:

Q: answer

Q: A projectile is aimed at a mark on the horizontal plane through the point of projection.It falls 12 ...

Q: An 80-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the b...

Q: 1500 16 1500 1b 153016 12-1AW R ol to eie nm 40006 4000 IL Determine th- Force in member AB, AC, BL,...

Q: F1 F2 F H 3 I G F A B. C Ed d d+d D tA-Determining the forces in three members on the right-hand sid...

A: Given-

Q: The angle between the prolongation of the preceding line and the forward line of a traverse is calle...

Q: Problem 2: Draw the shear and moment diagram of the indeterminate beam. 75KN 17KN/m 60KN 40KN 10KN/m...

Q: A truck becomes stuck in the sand at a local beach. To help, a friend takes a 50 ft long rope, ties ...

Q: dbject Sokg uotor

Q: The rigid you beam is Supported by a pin at A d wires BD and CE. IP the load Pon the beam ause the P...

A: A rigid beam is there which is supported by a Pin at A and a wire BD and CE. now a load P on the bea...

Q: -2 m

A: Step 1: Q=1000 kN Z=5.8 m r=0 r/z=0

Q: Q2) What is the lightest W-shape beam that will support the load shown in Fig. without exceeding a b...

A: To Determine The lightest W-shape beam that will support the load Actual bending stress in the beam.

Q: A cylindrical tank is being filled with water. The tank is initially empty but then water begins to ...

A: Given -

Q: a- 2M- d-2,5cM The beam of the cross section in the form of American standard Channel or C shape C10...

A: Given C shape C10×30, K1= 2.5, K2=6.8 The above diagram can be shown as ...

Q: Calculate the earth pressure at rest and distance at which the net at rest force acts.

Q: Classify the following soil using the U.S. Department of Agriculture textural classification. Gravel...

A: Reference : USDA - US Department of Agriculture Textural Classification Refer the figure established...

Q: One of the benefits of a close :command is Only close the square shape Connect the last point of the...

A: Asked: benefits of a close command.

Q: A 3-ft-thick (measured vertically) veneer of residual soil overlies a long rock slope inclined at 28...

Q: In your own words, what is the most significant event or invention made that contributed greatly to ...

A: Transportation was developed less than 250 years ago, but it is hard to imagine life before ships, t...

Q: No. 3. The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an ...

Q: rtical curve is required to pass through a fixed point that is located at station 314+00, elevation ...

A: PVCsta=PVIsta-L2PVCsta=31500-L2PVCelv=PVIelv-g1L2PVCelv=2430+0.025L2Equation of the curve :y=g2-g12L...

Q: The rate of flow of traffic on south expressway is 1200 vehicles in one hour. Find the space mean sp...

A: Flow= 1200 vehicle per hour Density= 25 vehicle/ km

Q: need the answer quickly

A: Given data- Average density (K) = 25 veh /km Speed (V) = 80km/hr

Q: Two spheres, each 1.3m in diameter, weigh 5kN and 13kN, respectively. They are connected with a shor...

Q: An asphalt road can be constructed for P 5M. It is estimated that resurfacing is needed very year fo...

A: Given construction cost = P 5000000 resurfacing cost= P 1000000 interest rate = 10% n = 5 yr

Q: A column is subjected to a total load (P) of 60 kN supported through a bracket connection, as shown ...

Q: The distance between two lines is determined in the multiline command by one of :the following optio...

A: The scale option of the multiline (MLINE) command defines the offset distance between multiline elem...

Q: A compound curve is composed of 3 and 5 degree curves with I1 = 22 degree and I2=30 degree, respecti...

Q: Water flows in a concrete rectangular channel (n = 0.013) that is 12.0 m wide and water depth of 2.5...

Q: A particle moves along a straight line with a velocity V = 12-312 m/s, where t is in seconds. When t...

Concept explainers

Sediment transport

Sediment transport or Soil transport is the movement of solid particles, usually due to the combination of gravitational forces acting on the sediment, and the movement of the liquid at which the sediment enters. Soil erosion occurs in natural systems where the particles are sandstones (sand, rocks), mud, or clay; the liquid is air, water, or ice; and the gravitational force that works to move particles to the landing surface. Sediment transportation or soil migration due to the movement of liquids occurs in rivers, lakes, lakes, oceans, and other bodies of water as a result of currents and waves. Transportation is also caused by glaciers as they flow, and to places on earth under the influence of wind. Soil erosion due to gravity alone is possible in most sloping areas, including hills, scarves, cliffs, and the continental shelf — the continental boundary of the slope.

Question

Three pipes steadily deliver water at 20°C to a large exit pipc in Figure 1. The velocity V;
= 5 m's, and the exit flow rate Q,= 120 m’/h. Find (a) V;; (b) V;; and (c) V, if it is known
that increasing Q, by 20% would increase Q., by 10%.
D, 6 cm
D; = 5 cm
D =9 cm
D = 4 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
Situation 1 Q. If the flow rate of water through the pipe system shown in the following figure is 0.050 m^3/s under total head loss of 9.0 m, assuming a C coefficient of 120 for all pipes determine the following, 1. The head loss in pipe B. 2. The flow in pipe B, in m3/s. 3. The diameter of pipe C.
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014 *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa
1. A rectangular channel has a contraction that smoothly changes the width to a minimum width of 1.5 f t (the throat). If the flow is critical at the throat, find the volume flow rate when the depth at the throat is 1.5 f t. 2. Water in an open channel of constant width flows over a bump of height 1 f t, as shown in Figure P10.10. What is the depth of the water Y2? Assume uniform flow of constant width with no losses.
High velocity water flows up an inclined plane, as shown in Figure 5 .1 What are the two possible depth of flow at section 2? Neglect al losses.
4. A reservoir supplies water to a horizontal 6′′ pipe 800 ft long. The pipe flows full and discharges into the atmosphere at the rate of 2.23 cfs. What is the pressure in psi midway in the pipe, assuming the only lost head is 6.20 ft in each 100 ft of length? indicaye free body diagram
Try making the flow net for the following diagram. Given: H1= 6m H2= 1.5 m D= 8m D1= 4m Draw a flow net
Diagram of the problem, necessary formulas, clearance and numerical solution Water circulates through a horizontal tube with a flow rate of 10 m3/s. Initially, the surface of the tube is 2 m2 and the section decreases until it reaches an area of 1 m2. The density of water is 1000 m3/s. a) What is the velocity of the water as it enters the tube?b) What is the pressure difference between the two sections.c) In which section of the pipe is the pressure greater?
An underground conical tank, standing on its vertex, is being filled with water at the rate of 18pi ft3/min. If the tanks has a height of 30feet and a radius of 15feet, how fast is the water level rising when the water is 12 feet deep? a. 3/4 ft/min b. 1/4 ft/min c. 1/2 ft/min d. 1/3 ft/min
A sluice gate, as shown in figure 01, is used to control the upstream water level in a3 m wide rectangular channeL The water discharge in the channel is 15 m3/s. You given the water depth at 3 to be 2.5 m and the hydraulic jump Froude number equation