Through a very narrow gap of height 'h a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity μ1, and on other side oil of viscosity μ2, Calculate the position of plate so that: (1) The shear force on two sides of plate is equal (2) The pull required to drag the plate is minimum

Through a very narrow gap of height 'h a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity μ1, and on other side oil of viscosity μ2, Calculate the position of plate so that: (1) The shear force on two sides of plate is equal (2) The pull required to drag the plate is minimum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 200-lb block is on top of a 300-lb block and both blocks are tied to a pulleya pulley that is attached to the wall, as shown in the figure. The coefficient of static friction between thetwo blocks is 0.3 and between the 300 lb block and the floor is 0.4. The coefficient of dynamic frictionbetween all surfaces is 0.25. Disregard the friction at the pulley.Determine the minimum force that must be applied to the 300 lb block in order for it to initiatemotion (imminent motion).
Flat plate of area 106 mm2 is pulled with a speed of 0.4 m/s. relative to another plate located at a distance of 0.1 mm from d. Find force and power (consider Dynamic viscosity = 2 poise)
Block on a rough surface weighing 400 N Angle of internal friction is 21.8⁰. Solve for the force P required to impend motion if the force is applied to block horizontally.
A beam with length L is FIXED at both ends. It is loaded with a concentrated force P at L/3 from the first support. (a) Draw the Loading Diagram. (b) Determine the deflection at midspan, EI is constant. (c) If the beam is made of steel, what is its elastic modulus? (d) If the beam has a length of 10 meters, cross section of 200x200mm, and force P is 10 kN, what is the deflection at midspan (in millimeters)?
Two plates each having and area of 5m^2 and and 37 mm apart. The plate on top is fixed while the plate located at the bottom is pulled using a force equal to 26 N resulting to a constant velocity of 45 cm/s. Determine the viscosity of the fluid filling the space in between the two plates.
Two blocks are connected by a light, flexible cable that passes a frictionless pulley. Block A weighs 500N and block B weighs 200N. The coefficient of static friction between A and the ramp is 0.30. Determine: (a) If the motion is impending down the plane, what is the tension force in the cable connecting Block A and Block B. (b) Are the two block in equilibrium state? 3 dec places pls
The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block A. The cutting angle is 30.296 degrees. Neglect friction. Computations must observe D`Alembert's Principle. a) Determine the normal force of contact between block A and block B. Express answer in Newtons or KiloNewtons.b) Determine the acceleration of block A. Express answer in meters per seconds.c) Determine the acceleration of block B. Express answer in meters per seconds.
vertical bar is loaded with axial loadsat points B, C, and D, as shown in the figure. Thebar is made of steel with a modulus of elasticityE = 29,000 ksi. The bar has a cross-sectional area of8.24 in2. Calculate the displacements at points B, C,and D. Ignore the weight of the bar.
length=7m height=250mm UDL on the beam=38.5KN/M d=812mm Mass of the beam=65.9kg/m a. Consider design loads( udl+self weight) b. Calculate and draw the Bending Moment Diagram (BDM).What is the value of the maximum bending moment? c. Calculate and draw the Shear Force Diagram (SFD).What is the value of the maximum shear force? d. Using the table, calculate the maximumdeflection of the beam.
Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by a rope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left?
The cylinder is subjected to a load that has a weight W. If the coefficients of rolling resistance for the cylinder’s top and bottom surfaces are aA and aB, respectively, show that a horizontal force having a magnitude of P = [W(aA + aB )]/2r is required to move the load and thereby roll the cylinderforward. Neglect the weight of the cylinder.
1. A 6 kg slider is released from rest at Point A and slides with negligible friction in a vertical plane along the circular rodshown below. The attached springhas a stiffnessof 520 N/m and an unstretchedlength of 0.6 m.a. Determine the change in potential energy when the slider is at B in joules. b.Determine the change in elastic potential energy when the slider is at B in joules c. Determine the velocity of the slider at B in meters per second.