to bring the process temperature back to the desired value. Once this calculation is complete the controller will produce an output signal that effects the change required. This output signal is known as the (manipulated value) and is normally connected to a heater, control valve, fan or some other "final control element" which actually injects or removes heat from the process. i. Draw the block diagram that represents the temperature controller mentioned above and label all the blocks ii. Define the function of each block in the diagram

to bring the process temperature back to the desired value. Once this calculation is complete the controller will produce an output signal that effects the change required. This output signal is known as the (manipulated value) and is normally connected to a heater, control valve, fan or some other "final control element" which actually injects or removes heat from the process. i. Draw the block diagram that represents the temperature controller mentioned above and label all the blocks ii. Define the function of each block in the diagram

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

You are an electrician working in a plant that uses programmable controliers to parform much of the logic for the motor controls. The plant produces highly flammable chemicals, so the programmable controllers use a 24-volt DC output that is intrinsically safe in a hazardous area. You are having trouble with the output modules of the programmable controllers that are connected to DC control relays. These outputs are going bad at an unusually high rate, and you suspect that spike voltages produced by the relay coils are responsible. To test your theory, you connect an oscilloscope to an output that is operating a DC relay coil and watch the display when the programmable controller turns the relay off. You discover that there is a high voltage spike produced by the relay. What device would you use to correct this problem, and how would you install it?
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
a) Buses are conductive routes in a microprocessor's circuitry. This means that there is potential for current to flow among the various parts. Expertly classify and explain the functions of these buses as they pertain to microprocessors.When talking about a microprocessor, b) what are the key distinctions between data and instructions?
In your insight, what are the control circuits that are integral to the operation of the microprocessor/microcontroller? Explain why control circuits are relevant in the operation of the microprocessor/microcontroller.
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. B.- After 15 min, your microcontroller must send the PWM signal with a 15% duty cycle of 10 ms to turn off the sprinklers in zone one.
5.- Design a microcontroller system to control a sprinkler controller that performs the following tasks. We assume that your microcontroller is clocked at 10 MHz and has a 16-bit free-running counter. The sprinkler controller system controls two different zones by turning the sprinklers within each zone on and off. To turn on the sprinklers in a zone, the controller needs to receive a 152.589 Hz PWM signal from its microcontroller. To turn off the sprinklers in the same zone, the controller needs to receive the PWM signal with a different duty cycle. D.-After 15 min, your microcontroller must send the PWM signal with a 25% duty cycle of 10 ms to turn off the sprinklers in zone two.
Given a state machine with the following state transition table. Draw the circuit diagram, and give me the logical expressions.
Show the program execution for the following program.The hypothetical machine has four (4) opcodes:1110 = LOAD0111 = STORE1000 = ADD
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.
Question 01: Present, in detail, the block diagram scheme of a model in state variables, including the controller and the state observer.Then, determine the range of values of “K1” and “K2” that make the system below observable and controllable. Finally, obtain the characteristic equation of this model.
1. With the aid of a diagram, explain the operations of a star-delta motor starter under reduced voltage. b. In producing a Printed Circuit Board (PCB), signal integrity is very important to consider. Briefly explain three (2) of the areas that is important for consideration
What are the types of controllers? Draw the block diagram for PID controller and state the áre applications.