TOP VIEW FRONT VIEW RIGHT SIDE VIEW PROBLEM:

Q: The civil engineering students calculate the overall strength of slab. they find that to its breakin...

A: When we have to calculate the overall strength of slab  then the minimum compressive strength for ga...

Q: Please answer with complete illustration. A cantilever slab has a span of 2.40 m. It is 150 mm thick...

A: Loads are external forces that can produce stress, deformation, displacement, and acceleration in a ...

Q: A complete-mix anaerobic digester is used to treat the sludge from primary sedimentation tank. The s...

A: 1. We know that ; Volatile solids = 1000 * SG12 Where ; SG = Specific gravity = 1.03 Volatile solids...

Q: Figure shows the side view of a tank with a curved gate. The gate width into the page is 18 in. The ...

A:

Q: A flexible pavement is constructed with 4 inches of hot-mix asphalt wearing surface, 10 inches soil ...

A: Given:- The depth of the hot-mix asphalt surface = D1 = 4 inch The depth of the soil cement base = D...

Q: 2. Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers...

A: step 1-

Q: In Horton's infiltration equation fitted to data from a soil, the initial infiltration capacity is 1...

A:

Q: a 10m simply supported beam has an overhang of 2m at the left support. If a moving uniform load of 9...

A:

Q: Seven-Day Maximum Pavement Minimum Pavement Temperature, °C Temperature, °C Recommended PG Grade 50%...

A: Condition that high/low temperature grade of pavement should satisfy: High temp. Grade ≥ mean maximu...

Q: 6. The L-shaped area on the ground surface carries a uniform 2000 psf load, as shown below. Find the...

A: (a) Vertical stress below point A Divide the area into three areas, A1, A2 and A3 Depth , z = 24 f...

Q: he local waste management agency has proposed to set up a waste combustion facility next to the exis...

A: Given:- The estimated landfill capacity remaining = 300,000 yd3  The capacity of combustion facilit...

Q: Question: Suppose a large rock is ejected from a volcano, as illustrated below with a speed of 25.0 ...

A: ASKED: To calculate the time taken by the rock to follow the given path.   Given, Initial speed of t...

Q: What is structural database testing, and how is it distinguished from other types of testing?

A: The 3 types of Database Testing are Structural Testing Functional Testing Non-functional Testing S...

Q: Draw the shear and moment diagrams of the given beam. Show your complete solutions. 10kN kN 10- m 5k...

A:

Q: Using the portal method, calculate for the magnitude of the moment reaction at support C. Express yo...

A: We have to determine the value of magnitude of the reaction at support C as per the given data in th...

Q: uired Mu = 1500 KN. M 70 fc = 28 MPa. fy 420 MPa. %3D

A:

Q: Draw the free-body diagram of the hand punch which is pinned at A and bears down on smooth surfaces ...

A:

Q: (a) how many pounds of lead weighing 700lb/ft^3 must be fastened to the outside bottom to make the c...

A: Downward weight will be balanced by bouyancy force.

Q: For the hottest month (June) of the year 2015, the following data is given: Summation of maximum tem...

A:

Q: A prestressed T beam shown which is reinforced with a bonded tendon having an area Aps = 1580 mm?, f...

A: Given Aps= 1580 mm2  f`c= 34.5 Mpa 

Q: An unsymmetrical parabolic curve has a back tangent of -5% and a forward tangent of +3%. If the leng...

A: G1 = -5% G2 = 3%

Q: /Find The location of the jump if formed ,use manning coe. = 0.015

A: Tail water depth play a important role in formation of jump at the location .jump can be classified ...

Q: Determine the shear and moments in the floor girder as a function of x. Assume the support at A is p...

A: ASKED: To write the shear and moment in the floor girder as function of x.

Q: E Question The velocity of a particle traveling along a straight line is v = (3t² - 6t) ft/s, where ...

A: Using the mathematical definition of velocity as the first derivative of time and knowing the initia...

Q: An 8 hp pump is installed near the reservoir container of oil having a s.g. Of 0.82. The rate of flo...

A:

Q: The stiffness coefficient 'k11' for the beam shown below is El 1 Internal Hinge - 2 m 3 m

A:

Q: The device shown is used for determining the shear strength of the wood. The dimensions of the wood ...

A: ASKED: To compute the average shear strength of the wooden block.   Given, Loaf at failure (P) = 12 ...

Q: 1. Calculate the degree of indeterminancy of the structure shown below.

A: Given data in question  Truss To find out  Degree of static indeterminacy  Note Ds = degree of stati...

Q: Key in the Redundancy number for the following structure. Key in -1 if the structure is unstable. No...

A:

Q: Situation 1 - An open cylindrical tank is 1.35m in diameter and 2.20m high is 2/3 full of water. 85....

A:

Q: The soil moisture in this zone is is near field capacity and moisture capacity lowers with depth A t...

A:

Q: The mass of the aggregates to be tested in Los Angeles Abrasion Machine is 10,000g, what is the % ab...

A:

Q: The rectangular footing shown in the figure is subjected to the following service axi- and moments: ...

A: Data DL=700 kN LL=450 kN B=3m D=2.5m To determine the maximum soil pressure:  

Q: Compute the stress increase in kPa below footing A (1.5m x 1.5m) at the center of the clay layer. As...

A: Given Data: The width of the footing A is bA=1.5 m. The load on footing A is QA=P1=400 kN.   To Dete...

Q: 2. A planned rigid loaded area 1.8 2.2 m and carries a uniformly distributed load of q-180 kN/m. Est...

A: Given Data: The length is L=2.2 m. The width is B=1.8 m. The uniformly distributed load is q=180 kN/...

Q: A group of 16 piles are arranged in a square pattern and installed in a deposit of soft clay. The di...

A: Ultimate capacity of pile is the sum of bearing capacity and friction resistance. For friction pile ...

Q: V=25 m's S cm đia. PQ = 200 k9/ 7 cm dia.

A:

Q: How much load must be applied on the wood, with a clear span length of 2350mm, deflection of the woo...

A:

Q: A horizontally laid circular pipe culvert having an elevation of its top to be 26m crosses at right ...

A:

Q: A rectangular tank 6 m. long by 1.8 m. deep is 2.1 m. wide contains 0.90 m. of water. Find the unbal...

A:

Q: A certain area has the following properties: Ix= 55 x 10°6 mm^ 4 ly = 120 x 10°6 mm4 Ixy = 55 x 10°6...

A:

Q: Determine the magnitude of the reaction Dx of the figure shown. 4 kN/m No KN. 2 kN/m -hinges- 12 m. ...

A: Draw the FBD of beams ABC and CD. Then using equilibrium equations the horizontal reaction can be ca...

Q: QI) A beam undergoes shear of V 27 kN, determine the web's shear stress at A and B. Indicate the she...

A: At point A and B first moment of inertia is equal hence shear stress at A and B will be same

Q: Determine the average values of strain components at point A shown.

A: Strain: - It is defined as the ratio of change in size to actual size of given object. Strain is uni...

Q: A simply supported beam is 10m long. It has an overhang of 2m at the right end. A highway load compr...

A: simply supported beam : A simply supported beam is one that is supported by only two points and can ...

Q: square pattern and installed in a deposit of soft clay. The diameter and length of each pile is 250 ...

A:

Q: A soil sample has a unit weight of 105.7 pcf and a saturation of 50%. When its saturation is increas...

A: given- case-1unit weight γ1=105.7 pcfsaturation s1=50%=0.50case-2unit weight γ2=112.7 pcfsaturation ...

Q: 3 possible biological hazards in construction site excavations, it’s causes, prevention and control.

A:

Q: A uniform wheel of 600 mm diameter, weighing 5 kN rests against a rigid rectangular block of 150 mm ...

A:

Q: The project team for a LEED-NC project is confident that they can earn 50 points and meet the prereq...

A: Answer is Option :4