Tötal Weight A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of 300 kN. Determine the required area of the reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. 3 ft 6 ft 1 ft Use Eco = 14 GPa and Est = 200 GPa.

Tötal Weight A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of 300 kN. Determine the required area of the reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. 3 ft 6 ft 1 ft Use Eco = 14 GPa and Est = 200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 250 mm wide rectangular concrete beam is reinforced for tension only. The beam has an effective depth of 300 mm. fc’ = 9.3 MPa, fs = 138 MPa, n = 9. Use working stress design for balanced condition. 1. Which of the following most nearly gives the value of k. a. 0.3225 b. 0.3526 c. 0.6234 d. 0.3775 2. Which of the following most nearly gives the value of j. a. 0.7482 b. 0.8472 c. 0.8742 d. 0.4278 3. Which of the following most nearly gives the balanced moment capacity of the beam in kN.m. a. 34.52 b. 45.36 c. 36.7 d. 32.3
The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the working stresses for steel and concrete are 345 MPa and 28 MPa, respectively, determine the largest axial force P that can be safely applied to the column. Use Est=200 GPa and Econcrete=25 GPa.
The steel rod is stress-free before the axial loads P1 1⁄4 150 kN and P2 1⁄4 90 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E 1⁄4 200 GPa.
Calculate thr A) ultimate column loads B) upward ultimate soil pressure C) footing effective depth "d" for the long span and the short span
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa a. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = ____ mm (2 decimal places) b. What is the condition of failure? = ____ (Balanced, Tension controlled, Compression controlled, Transition) c. Calculate the design moment strength of a typical interior beam. = ____ kN⋅m (whole number)
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the depth of the rectangular compression stress block? A. 188.15 mm B. 151.93 mm C. 139.51 mm D. 118.58 mm
NOTE!! ONLY ANSWER D, E, AND F. THANK YOU. A section of a gravity masonry dam is shown in the figure water is flush at the top of the dam upstream and 5m from the ground downstream. Assume hydrostatic uplift to vary uniformly from full hydrostatic pressure from the heel to zero at the drain density of water is 1000kg/m^3. The specific gravity of concrete is 2.4. Determine: a. The location of the resultant force b. Factor of safety against sliding if coefficient of friction is 0.75 c. Factor of safety against overturning d. Stress at the heel and the toe e. Unit horizontal shearing stress at the base f. Factor of safety against overturning neglecting uplift NOTEEE!!! (Only answer D, E, and F)
A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. 1. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. 2. Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. 3. Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight.
A rectangular beam of length 702mm has a width of 132mm and a depth of301mm. Compression steel bars are placed at a distance 98 mm from the extreme concrete compressivefiber. The beam supports service dead loads of dead load (16 KN/m) and live load (24 KN/m). Reinforced with 4 25mm tension steel bars and 4 12mm tension steel bars f′c = 42 MPafy = 519 MPa 1. Solve for the height of the neutral axis measured from the extreme compression fiber.2. Solve for the design moment.3. Solve for the strength reduction factor.
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3- 22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPa). fc' = 28 MPa a. determine the effective depth of the beam b. determine the depth of compression block c. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam
A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 4-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 24 MPa and rebar strength fy = 280 MPa. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. (A to D) Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. (E to H) Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight. (I to L) A. 44.15 B. 78.85 C. 57.34 D. 98.56 E. 195.66 F. 89.60 G. 133.91 H. 110.15 I. 16.31 J. 39.16 K. 26.16 L. 20.51