Transcribed Image Text: A household electrical device with a capacity of 2800 watts, equipped with a voltage source of (220 volts), and the length of the supplied wire path is 60 meters. Calculate: 1- The area of the wire cross section to be established, provided that the drop in voltage on the wires does not exceed 5% 2- The amount of the voltage drop on the wires 3 - Voltage of the load that supplies the load 4- Amount of percentage

Transcribed Image Text: A household electrical device with a capacity of 2800 watts, equipped with a voltage source of (220 volts), and the length of the supplied wire path is 60 meters. Calculate: 1- The area of the wire cross section to be established, provided that the drop in voltage on the wires does not exceed 5% 2- The amount of the voltage drop on the wires 3 - Voltage of the load that supplies the load 4- Amount of percentage

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter13: Lighting Branch Circuit For The Living Room

Section: Chapter Questions

Problem 16R

See similar textbooks

Similar questions

here are 240 square meters of floor area in a house that contains an electric range rated as 12 kW and an electric dryer rated at 5000 watts. Calculate (a) the minimum size of feeders (service conductors) required.
When applying the general provisions for receptacle spacing to the rooms of a dwelling unit, which require receptacles in the wall space, no point along the floor line in any wall space of a dwelling unit may be more than——- from an outlet. A. 12ft. B. 10ft. C. 8ft. D. 6ft.
A house has the following specifications for a circuit. Determine the size of the circuit breaker, wire, and size of pipe to be used for each circuit and the service entrance. Show a detailed computation and also tabulate the final answer. 15 lighting outlets1 kitchen range12 lighting outlets1 water heater at 1500 watts12 convenience outlet8 convenience outlet9 convenience outlet12 lighting outlet3 convenience outletspare-1500 wattsspare- 1500 watts
The dwelling has a floor area of 142 sq. m. It has a typical household appliance including one 8 kW electric range, one 1 Hp room air-conditioning unit, one 3 Hp room air-conditioning unit and one 1 Hp water pump. (Draw the diagram) Determine the following: Total Load:A) Service Entrance ConductorsB) Service EquipmentC) Other Load
An electrician installs five 3 AWG THWN copper current-carrying conductors in a raceway located in a garage. The garage area is subject to an ambient temperature of 100°F. All terminations are rated at 75°C.Ampacity: __________ Maximum Fuse or Circuit Breaker Size: __________.(NO CHAT GPT, ONLY NEAT HAND WRITTEN SOLUTION PLEASE.)
The NEC states that the neutral conductor of a three-wire branch circuit supplying a household electric range with a maximum demand of 8.75 kW shall be permitted to be smaller than the ungrounded conductors. However, the neutral ampacity shall not be less than ______ percent of the branch-circuit rating and shall not be smaller than 10 AWG. A. 30 B. 70 C. 50 D. 8.75
How many total packages of C4 (M112) are required to cut 45 trees with the average diameter of 26 inches using a ring charge? 440 495 500 580 What is the correct answer?
All of the following are NOT included when calculating the usable area of a dwelling to compute the required lighting load, EXCEPT for ____. Select one: a. open porches b. crawl spaces c. unfinished basements d. garages
A certain company is required to power up its lighting devices using Solar power. System requirement:24 Volts System, 36 Amperes SystemAvailable Solar Panel to use:100 W, 12 V, 6 AmperesDesign the Solar Panel Array to satisfy the requirement of the company, assuming battery pack is already good and settled. Draw connections and show computations
All components of an exposed wiring system, installed where walls are frequently washed, must be mounted with a minimum of _____ in. airspace between components (boxes, fittings, conduits, etc.) and the wall (supporting surface). Select one: A. 1/4 B. 1/8 C. 1/16 D. 1/2
1. Diagram the floor plan for the main floor of your home. Locate the service entrance panel. If it is located on the main floor, draw its location on your floor plan and label it "S.E.P." If it is not on the main floor, add some text on your floor plan that informs the reader of its location. Next, locate every switch, receptacle (accessible ones only), lighting fixture, and fan fixture on the main floor of your home. Refer to the Table of “Electrical Symbols andOutlets” and place those symbols that correspond to the items on your floor plan in the approximate location they are found in the rooms. Draw dashed lines from switches to the lighting fixtures, split-circuit receptacles (those controlled by a switch) or the fans they control. Create a tabulated load schedule of your home. 2. Examine the Sample Residential Electrical Plan and notice how the symbols are used. Answer the questions that are found below the electrical plan.
13/ A combination of various electric elements, connected in any manner whatsoever is known as Electrical network. Select one: True False