True/False Manual load calculations should be considered only for preliminary design or simple building

Q: 900 lb 60 lb/ft 400 lb D A |B - 8 ft 6 ft→ 4 ft

A: following is the solution-

Q: check the equilibrium conditions For the following system F 400 lb fied ? Tina ation:- 30 = 300 lb -…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: specific enthalpy, specific internal energy, specific volume and specific kinetic energy has the…

A: Intensive properties are mass independent and extensive properties are mass dependent.  Specific…

Q: Which of the following statement is correct? Select one: O Datum energy is potential Energy…

A: Potential energy: An object which is at some position then it holds some energy that energy is known…

Q: Apart from the breaking system,state two other means by which the speed of a vehicle can be reduced

A: Other than conventional braking, the methods that can be employed to reduce the speed of a vehicle…

Q: A small aircraft with a weight of 700kg was able to climb 300m within two minutes. How much power…

A: Given data Mass of air craft = 700 kg Additional elevation to climb = 300 m Time required = 2 mins =…

Q: What is the type of industrial process of the following production: (i) Latex Glove. (ii)…

A: i) Latex concentrates are blended with different compounding chemicals sometimes recently being…

Q: HIRARC can be defined as, А. Hazard Identification, Risk Control & Risk Assessment Hazard…

A: HIRARC can be defined as

Q: AP W h mg ΔΡ + Az +

A: The above given equation is Bernoulli's equation. Every term of Bernoulli's equation has units of…

Q: (ii) What is the recommended safe practice for the disposal of solid industrial waste?

A: There are different type of methods practiced for the solid industrial waste disposal are :…

Q: Small explanation. Aerodynamic lift results from ________ Principle.

A:

Q: Which of the following is not one of the socio-economic impacts of transportation? A ) Time B )…

A: Mobility opportunities

Q: If a closed system undergoes an isochoric process, the thermodynamic work for this process is always…

A: Q1. It is required to determine if a if a closed system undergoes an isochoric process whether the…

Q: Q1/ Dose heat capacity affect the body"s cooling and heating processes Give an example

A: We are suppose to solve only one question. Please post other question as a separate question.   Heat…

Q: A 50 Horsepower Diesel Engine with a brake thermal efficiency of 30% uses fuel oil with HV=18500…

A: Brake power of Diesel engine, B.P.=50 HPBrake thermal efficiency of the engine, ηbth=30 %Heating…

Q: Heating fuels, also known as heating oils, are heavier so they are developed towards the end of the…

A: Solution:

Q: In constant pressure process, sensible heat is zero Standard state is at 1 atm and 25 ⁰C Water…

A: To select the correct option.

Q: Which of the following having a direct contact with physical quantity?

A: Which of the following having direct contact with physical quaintly? Answer: b) Bourdon tube

Q: Water, Water Oil ds = 8" di = 10" 4" d4 = 5" d2 = 3" d3= 4" E. Hg Given: Yw = 62.4 lbf/ft³ = 847…

A: GIVEN DATA A DIFFERENTIAL MANOMETER GIVEN WE HAVE TO FIND PRESSURE DIFFERENCE NOTE- CONVERT REQUIRED…

Q: A building has three boilers to provide heat. Each boiler has a 150.000 BTU/Hr capacity. On a design…

A: Given:  There are 3 boilers each of capacity 150,000 BTU/hr capacity.  1 boiler Capacity = 150,000…

Q: Differentiate between a hazard, a risk, an accident and a near miss.

A: Difference between a hazard , a risk ,an accident  and a near Miss.           Note :- you have…

Q: Fg= 900 N A Fc= 600 N 6 m 3 m 45 B 45m 6m

A:

Q: In oil and gas field, safety in work place is needed. Why?

A:

Q: Which of the following statement(s) is(are) correct? a. For closed system operating adiabatically,…

A:

Q: Which case shows the least acceleration? 20 lb 15 lb A 45° 45° 45° E 15 Ib

A: GIVEN:

Q: Which of the following has the lowest calorific value ?  I) coal  ii) charcoal  iii) wood  iv)…

A: calorifie value:  When we burn a unit mass of any fuel completly then amount of heat produced by…

Q: The Rockwell hardness C test uses a major load of ... Select one: a. 3000 kgF O b. 3000 N O c. 10…

A: Option c is correct.

Q: 11 kg of steel has an original temperature of 210°C. If gains heat to the value of 710 kJ, what is…

A: Given Data Q=710 kJ m=11 kg Ti=210°C C=450 J/kg.K

Q: which of the following statements holds true? what is the answer a. temperature is an extensive…

A: It is required to determine correct statement

Q: For each of the following systems, give two examples of how a mechanical engineer would be involved…

A: Most of the machines and equipment that emit heat can be studied under Thermal Engineering section…

Q: are the gases that comes from the burning of fossil fuels, causes acid rain. a) SO3 & HNO2 b) SO₂ &…

A: According to the details provided in the question, we need to explain the above problems.

Q: The possibility for accidental mechanical damage in the automotive shop i

A: Depending on the intensity of the impact, the vehicle's foundation may be damaged. Your vehicle's…

Q: Note/ I want solve question What does utilitarianism tell us about the behavior of the Aberdeen…

A:

Q: 13/. Acidity is the _________ property of the material. a. thermal b. mechanical c. chemical d.…

A: Thermal properties: Specific heat, conductivity,  coefficient of expansion  etc. Mechanical…

Q: A  washing machine  has a power rating of 1360 W. How much energy does this appliance consume in one…

A:

Q: A washing machine has a power rating of 1360 W. How much energy does this appliance consume in one…

A: Since nothing is given about how long the machine is used, assume that it is used continuously for 1…

Q: A boy and is dad put a rope around a tree and stand side by side. What force by the boy can resist a…

A: Given : T1=800 Nμ=0.5θ=180° T1 stands for the force applied by the dad.

Atomic diffusion in solids

In material science, diffusion can take place in solid, liquid, and gases. In solids, atomic diffusion can take place with the help of thermally activated and randomly vibrating atoms. The atomic diffusion in solids is complex and very slow in comparison to atomic diffusion in liquids and gases because the interatomic distance between the atoms is smaller in solids as compared to liquids and gases.