Two bars, a pulley, and a cable are used to sup- The two bars have port a block as shown in Fig. negligible weight. The mass of the puiley is 50 kg and the mass of the block is 100 kg. Determine the internal resist- ing forces and moment transmitted by cross section aa in bar AB. 300 mm в 300 mm 550 mm 350 mm 300 mm 300 mm W

Two bars, a pulley, and a cable are used to sup- The two bars have port a block as shown in Fig. negligible weight. The mass of the puiley is 50 kg and the mass of the block is 100 kg. Determine the internal resist- ing forces and moment transmitted by cross section aa in bar AB. 300 mm в 300 mm 550 mm 350 mm 300 mm 300 mm W

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Similar questions

The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
the bar supported by a pin at a and a cable at b carries a load of 260 nat c. neglecting the weight of the bar, a.) determine the normal force 3 m from a. b.) determine the shear force 3 m from a c) determine the bending moment 3 m from a d.) determine the torsion 3 m from a 605 b 5 m 4m 12 260 n
The bar supported by a pin at A and a cable at Bcarries a load of 260 N at C. Neglecting the weight of the bar,a.) Determine the normal force 3 m from A.b.) Determine the shear force 3 m from A.c.) Determine the bending moment 3 m from Ad.) Determine the torsion 3 m from A
Bent rod ABC is supported by a pin and bracket at A and a cable at C to D. The weight of the bent rod is 7.00 N/m and triangular distributed load is applied from point B to C as shown 1-2: See questions in image 3. What approximates the tension force? 4. What is the magnitude of the resultant of the triangular distributed load, F_BC, and its location d?
The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces immediately to the left of the load.Template: (On CD) F= 270 N; M=43.2 N.m; V = 90 N
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Magnitude of the reaction force at A in kN = 34.8 Determine the magnitude of the moment of P about the x-axis in Nm
Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.
Force P is applied as shown on the 13.5 mm thick plate. P = 100 kN. Holes are oversized causing all rivets to always proportionately react to load applied on the plate. 1. Which of the following most nearly gives the force in rivets if P is applied at the centroid of four(rivets)? a. 50 kN b. 30 kN c. 25 kN d. 40 kN 2. Which of the following most nearly gives the force in rivets if only moment equals P times e is applied at the centroid of four(rivets)? a. 12.567 kN b. 10.451 kN c. 32.672 kN d. 17.678 kN 3. Which of the following most nearly gives the maximum force in rivets due to combined effect of P and torque? a. 42.28 kN b. 40.93 kN c. 39.53 kN d. 37.34 kN 4. Considering shearing in bolts, what is the minimum required diameter if allowable shearing stress in bolts is Fv/2, Fv = 372 MPa a. 27.34 mm b. 14.53 mm c. 16.45 mm…
Find the magnitude and location of the resultant force on the cylindrical arc shown in Fig. (10) in each of the following two case: a. Pg=120.11 KPa (abs) b. Pg=90.68 KPa (abs) The arc is 25m long (normal to the paper)
Question 3. Determine the crippling load for a I-section of dimensions 12 cm × 12 cm × 2 cm and of length 5 m when it is used as a strut with both of its ends fixed. Take E = 2 × 105 N/mm2.
Hinge pin P is loose through bracket tube, there is a small gap between tube and bracket at point A. Determine the frame tube reactions at A and B associated with the weight L of a person 80.0 kg.
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN