Two brass rods and one steel rod to- gether support a load as shown in Fig. brass and steel are not to exceed 60 Nimm2 and 120 N/mm?, find the safe load that can be supported. Take E for steel - 2 x 105 N/mm? and for brass = 1 x 105 N/mm2. The cross- sectional area of steel rod is 1500 mm? and of each brass rod is 1000 mm2. If the stresses in %3D

Two brass rods and one steel rod to- gether support a load as shown in Fig. brass and steel are not to exceed 60 Nimm2 and 120 N/mm?, find the safe load that can be supported. Take E for steel - 2 x 105 N/mm? and for brass = 1 x 105 N/mm2. The cross- sectional area of steel rod is 1500 mm? and of each brass rod is 1000 mm2. If the stresses in %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and crosssectional area equal to 1000 ??2 fits snugly between two rigid walls. Determine the change in length due to the applied load. Use ? = 0.30. (Answer in three decimal places and in mm)
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
A 2 m long steel wire is fixed and hanging vertically with a tensile loadof 2 kN and causes it to stretch by 4 mm. Determine the diameter ofthe steel wire when the modulus of elasticity is 205 GPa.A. 3.5 mm B. 5.5 mm C. 4.5 mm D. 2.5 mm
A 14 ft, W10x54 column is pinned at one end and fixed at the other. What is the buckling stress of the column in ksi? Use E = 29,000 ksi and report your answer to two decimal places the answer is 135.63 please show steps!
The adjacent sketch indicates a brass wire which is exactly 12.00 m long and a steel wire which is 12.01 m long. Each wire has a cross-sectional area of 150 mm2 . What load does each wire carry if E steel = 200,000 MPa & E brass = 110,000 MPa? (Hint: no load on steel wire until brass wire stretches by 10mm, then ratio of stresses in each wire is same as ratio of E v
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
33333. From the given beam loaded as shown, Let P = 3 kN, L = 7 m, a = 3 m. E = 200GPa, I = 2000 x 10^6mm^4
N.6.1. Find principle stress if the values are as given: Upper side stress:300lb/9pulg2 Tangential in right direction: 120 lb/pulg2
Read the question carefully and give me right solution according to the question. Note: observe the given diagram and load carefully
Compute using Euler's formula: A square aluminum bar is to support a load of 65kN on a length of 4.50 m. Assume pinned ends, Determine the length of each side E = 70 GPa.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 404 mm2, 642 mm2 , and 271 mm2 respectively.Determine the change in length (in mm) of the bar if P = 28943 N.The moduli of elasticity are 80.75 GPa for bronze ,73.14 GPafor aluminum , and 203.66 GPa for steel . Round off the final answer to four decimal places.
If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is an inverted T with a 1'' by 8'' stem and a 1'' by 4'' base, as shown. The cross section has a moment of inertia of 97 in4 and its neutral axis is given. Pay attention to units, and calculate your answer to 1 decimal place. Determine the allowable maximum bending moment of the beam based on the allowable bending stress in tension, M allow: ____ kip-in.