Two impedances Zi and Z2 are connected in parallel across a 230 V, 50 Hz supply. The impedance, Zi consists of a resistance of 14 2 and an inductance of 16 mH. The impedance, Zz consists of a resistance of 18 2 and an inductance of 32 mH. Calculate the branch currents, line current and total power factor. Draw the phasor diagram showing the voltage and currents. Pag 14 2 ww 16 mH 18 2 ww 32 mH 230 V, 50 Hz lügure ?

Two impedances Zi and Z2 are connected in parallel across a 230 V, 50 Hz supply. The impedance, Zi consists of a resistance of 14 2 and an inductance of 16 mH. The impedance, Zz consists of a resistance of 18 2 and an inductance of 32 mH. Calculate the branch currents, line current and total power factor. Draw the phasor diagram showing the voltage and currents. Pag 14 2 ww 16 mH 18 2 ww 32 mH 230 V, 50 Hz lügure ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a three-phase Ynyn0 connected transformer. The equivalent impedance per reduced phase of the transformer to the primary is Zeq1= 1+j5 Ohm. The nominal primary voltage is V1Ln= 5920 V and the conversion ratio is a= 10. what is the amplitude of the actual voltage falling on one phase of the specified load? (simplified equivalent circuit will be used).
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, and admittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal place.Thank you!
Kindly answer letters d, e, f, g A 25 ohm resistor connected in series with a coil of 50 ohm resistance and 150 mH inductance. The combination is connected across the 220 V source. Calculate for the (a) power factor; (b) impedance; (c) true power; (d) graph the impedance triangle; (e) graph the power triangle; (f) show via phasor diagram the behavior of the current and voltage; (g) plot the sine wave equation of the current and voltage.
an R-L circuit takes a current of 7amp that lags behind the 231-volt source by 35elec deg. calculate the power factor, power, impedance, resistance, and inductive reactance of the circuit.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
PLEASE ANSWER LETTERS D & E A 25- W resistor, a 300-mH, and a 40-µF capacitor are connected in parallel across a 120-V, 50-Hz source. Determine the magnitude of the following: (a) admittance; (b) current through resistor, inductor, and capacitor; (c) the total current; (d) true power, inductive and capacitive reactive power; (e) apparent power, power factor, and power factor.
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
Suppose an AC generator with V(t) = (150V)sin(100t) is connected to a series LRC circuit with R=40 Ohm, L=80 mH, and C=50 microFarad, as shown in figure. Calculate the maximum voltage across the resistor (VR0)?
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
A 25- W resistor and a 40-µF capacitor are connected in parallel across a 120-V, 50-Hz source. Determine the magnitude of the following: (a) admittance; (b) current through resistor and capacitor; (c) the total current; (d) true power and capacitive reactive power; (e) apparent power, power factor, and power factor.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage