Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If F₁-540 N and F2- N, determine the vector expression for the resultant R of the two forces. Then determine the magnitude R of the result and the angle which it makes with the positive x-axis (measured counterclockwise from the x-axis).

Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If F₁-540 N and F2- N, determine the vector expression for the resultant R of the two forces. Then determine the magnitude R of the result and the angle which it makes with the positive x-axis (measured counterclockwise from the x-axis).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the magnitude and direction of the friction force when theta=35deg and P=200N
1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. E =210 GPa. 100 | Cross section 6KN.m 2m B8KN 2 kN/m 2m T ) B8KN 2m
Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If = 540 N and = 300 N, determine the vector expression for the resultant R of the two firces. Then determine the magnidtude R of the resultant and thew angle which it makes with the positive x-axis (measured counterclockwise from the x-axis). 716.33 N, 17.18o 761.33 N, 17.81o 765.33 N, 17.28o 756.33 N, 18.72o
a 690N block is resting on an inclined plane and is subjected to a constant force of 875N acting parallel to the inclined plane. After the block has moved 4.69m from rest along the inclined plane, the force 600N is removed. The inclined plane has a slope of 4 vertical and 3 horizontal. Coefficient of friction is 0.23. a. Which of the following gives the distance that the block will move further along the inclined plane until it stops. b. Which of the following gives the velocity of the block when the force 875N was removed. c. Which of the following gives the velocity of the block when it returns to its initial position?
If M1 = 180 lb ⋅ ft, M2 = 90 lb ⋅ ft, and M3 = 120 lb ⋅ ft,determine the magnitude and coordinate direction anglesof the resultant couple moment.
If F1 = 100 N, F2 = 120 N, and F3 = 80 N, determine the magnitude and coordinate direction angles of the resultant couple moment.
(a) Draw qualitatively the deflection curve based on the bending moment diagram. (b) Determine the deflections at B and D, and the slope at C by the moment area method. (c) Locate the point of maximum deflection in AB and compute its magnitude. (E = 200GPa, I = 107mm4 )
A couple of magnitude M = 54 lb-in and the three forces shown are applied to an anglebracket. (a) Find the resultant (single equivalent linear force) of this system of forces. (b) Locatethe points where the line of action of the resultant intersects the lines extending through points AB and B-C.
For the simply supported beam carrying the concentrated load P = 171 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 1.79 m, E = 10.23 GPa , and I =1619497mm4.
A Block weighing 100N is held on a 400 incline by a Bar attached to a 150N Block on a horizontal plane. The Bar which is fastened by a smooth pin at each end is inclined 200 above the horizontal. The angle of Friction between each Block and its Plane is 180. Find the horizontal Force P applied to the150N Block which will cause it to be on the point of moving to the right?
A rectangular reinforced concrete beam with width of 300 mm & effective depth of 600 mm is subjected to a service bending moment of 200 kN.m. The beam is reinforced with 4-32 mm diameter bars. n = 8. 1. Compute the distance kd? a. 246.33 mm b. 353.67 mm c. 170.33 mm d. 302.33 mm 2. Which of the following gives the moment of inertia about N. A.? a. 4173.81 x 106 mm⁴ b. 3471.81 x 106 mm⁴ c. 4371.81 x 106 mm⁴ d. 4713.81 x 106 mm⁴ 3. Which of the following most nearly gives the maximum stress in steel in Mpa? a. 100 b. 110 c. 120 d. 130
11 A cylindrical caisson having an outside diameter of 9 m floats in sea water with its axis vertical and its lower end submerged 9 m, below the water surface. If its center of gravity is on the vertical axis and is 3.6 m above the bottom. a. Determine the value of ??? b. Find the true metacentric height. c. Find the righting couple when the caisson is tipped through an angle of 8°