Two large fixed parallel planes are 240 mm apart. The space between the surfaces is filled with oil of viscosity 0.81 N.s/m.A flat thin plate 0.5 m area moves through the oil at a velocity of 0.6 m's. Calculate the drag force (i) when the plate is equidistant from both the planes, and (if) when the thin plate is at a distance of 80 mm from onc

Two large fixed parallel planes are 240 mm apart. The space between the surfaces is filled with oil of viscosity 0.81 N.s/m.A flat thin plate 0.5 m area moves through the oil at a velocity of 0.6 m's. Calculate the drag force (i) when the plate is equidistant from both the planes, and (if) when the thin plate is at a distance of 80 mm from onc

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.26P

See similar textbooks

Similar questions

A piston 796 mm diameter and 200 mm long works in a cylinder of 800 mm diameter. If the annular space is filled with lubricating oil of viscosity 5 centipoise, calculate the speed of descent in m/s of the piston in vertical position. The weight of the piston and the axial load are 9.81N.
Using the information given in Table 10.4, determine the ratio of local pressure and density to sea-level values. Estimate the value of air density at the cruising altitude of most commercial airliners.
For a new sailboat, a designer wants to determine the drag force that may be expected at a given speed. To do so, she places a model of the proposed hull in a test channel and uses three cables to keep its bow on the centerline of the channel. Dynamometer readings indicate that for a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Determine the drag force exerted on the hull and the tension in cable AC.
How you find minimum drag and velocity from the equations
A wheel tractor has a 200HP engine.if it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. Calculate the available rimpull of this tractor. Take rimpull efficiency as 85%
Calculate Induced Drag please
A particle of 2 mm in diameter and density of 2500 kg/m3 issettling in a stagnant fluid in the Stokes’ flow regime.a) Calculate the viscosity of the fluid if the fluid density is 1000kg/m3 and the particle falls at a terminal velocity of 4 mm/s.b) What is the drag force on the particle at these conditions?c) What is the particle drag coefficient at these conditions?d) What is the particle acceleration at these conditions?
Assume the gross weight of the airplane is 600 lbs, what would be a reasonable estimate of its wing loading. *Use significant assumptions and solve this for propellers andjets.
A) What is an adverse pressure gradient, and where does it occur on an airfoil (Show that onan airfoil using a free hand sketch)?B) What causes the flow to separate from an airfoil?C) What are the two major consequences of flow separation?D) A B-2A aircraft is flying at H ft in standard day conditions at a velocity V kn. If the meanchord length is C ft.i- Find the overall or total Reynolds number for the aircraft.ii- Find the percentage of the wing chord where laminar flow is present, if Reynoldsnumber is 500,000.
Consider a soap bubble 2 mm in diameter and a droplet of water, also 2 mm in diameter, that are falling in air. If the value of the surface tension for the film of the soap bubble is assumed to be the same as that for water, which has the greater pressure inside it? (a) the bubble, (b) the droplet, (c) neither—the pressure is the same for both.
Answer the following question: 1. Air with pressure, temperature and density corresponding to a standard altitude of 12 km is allowed to expand isentropically to a state where temperature is 100 K. Calculate the pressure, specific weight and density after the expansion.
The purpose of this problem is to give you a feel for the magnitude ofReynolds number appropriate to real airplanes in actual flight. a. Consider the DC-3 shown in (1.1). The wing root chord length(distance from the front to the back of the wing where the wing joinsthe fuselage) is 14.25 ft. Consider the DC-3 flying at 200 miles perhour at sea level. Calculate the Reynolds number for the flow over thewing root chord. (This is an important number, because as we will seelater, it governs the skin-friction drag over that portion of the wing.)b. Consider the F-22 shown in (1.5), and also gracing the cover ofthis book. The chord length where the wing joins the center body is21.5 ft. Consider the airplane making a high-speed pass at a velocityof 1320 ft/s at sea level (Mach 1.2). Calculate the Reynolds number atthe wing root.