Two parallel connected loads A and B are supplied by a 440 V line to line, 3-phase, 60 Hz generator. Load A draws an apparent power of 100 kVA at 0.80 pf lagging and load B draws an apparent power of 70 kVA at unity pf. Determine the line current supplied by the source.

Two parallel connected loads A and B are supplied by a 440 V line to line, 3-phase, 60 Hz generator. Load A draws an apparent power of 100 kVA at 0.80 pf lagging and load B draws an apparent power of 70 kVA at unity pf. Determine the line current supplied by the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Related questions

Q: B-Give one example for the followings: 1- direct method of measurement. 2- indirect method of…

A: We are authorized to answer only three question at a time since you have not mentioned which…

Q: 2. Yparameters=? 6 Ω 32 6 6Ω 3Ω

A: Y-parameter. This is 2*2 admittance matrix and also called short circuit admittance parameter in the…

Q: Which of the statements is not true about parallel connections? A) The total resistance is the…

Q: If the total number of levels of a quantizer is 8 and the step size delta-2V, determine the noise…

Q: 8. R₁ G₁ 6₂

Q: single phase bridge inverter has a switching sequence that produces a square wave voltage across a…

A: As per Bartleby policy we can answer only three sub parts. As you have not mentioned so I am solving…

Q: Quà L) transistor can be used as a electrical switch (T/F) 2) Consider the following robot…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: how hydropower water turbine energy refinement is essential in dry season

A: The Given is related to fluid mechanics and hydraulic machinery.

Q: 1. Determine the output voltage of this circuit for two different input voltage volts, assuming the…

A: Solution- 1. For Vin = 5V Diode D1 is in reverse biased condition , and diode D2 will conduct. I =…

Q: 1- You can find a band pass filter's center frequency with an oscilloscopé by increasing the input…

A: Brief description: For the above given questions we need to justify correct answers with the proper…

Q: 1. Describe the constructional features and characteristics, of a induction motor that would be used…

A: A DC shunt motor is a motor that runs at a constant speed. Because lathe machines must run at a…

Q: The load in each phase of a delta connected network is equal to 82∠54 Ohms. The network is connected…

Q: A potential energy function for a system in which a two-dimensional force acts is of the form: 2 U =…

Q: Example Sketch | Eal and fat for 32 2018| ये T 8 ZzzZ KR2-1 S-C

Q: A residential motor has a given voltage having an equation v=94sin3t. What is the frequency of the…

A: In this question, We need to determine the frequency of the motor, time taken to complete 1/8…

Q: phasor analy ques domain) of t circuit shown below. Replace the left part of the terminals A-B by…

A: Given the circuit, as shown below: Using phasor analysis techniques we need to determine the…

Q: Q5. A resistor (R) is connected with a capacitor (C) in series to a voltage source of v(1).…

Q: able 1: Oscillator circuit parameters and circuit components C2 = 5100 pF; Amplifier gain = 11;…

A: It is given that: C2=5100 pFAmplifier gain=A=11R1R2=C2C1f=20 KHz

Q: Example Sketch | Eal and Isal for λ 32 dzorgi 7 T 7 4 8 Zg2Z Zo KR2-1 S-C

Q: For PAM signal calculate sampling frequency, pulse width, power of PAM signal at 1k ohm and draw…

A: Here we discuss about PAM signal. NOTE :- As per our company policy, only FIRST 3 sub-parts of a…

Q: can watt hour can convert into volts

Q: 3. Write the differential equation for the system shown in Figure R(s) 55 +254 +45³ +²+4 C(s) 5+755…

Q: A transformer has a turn ratio of 4:1. What is the peak secondary voltage if 110 Vrms is applied to…

A: In this question, We need to choose the correct options Assume forward bias voltage of si diode =…

Q: Example13/ Find |Ed| at d=0, λλ 3λ λ 5λ 6λ σλ '8'4' 8 8 8 8 KR=1L 0° Draw standing wave pattern…

Q: For the network, determine IE, VC and VCE. show complete solutioions

A: Brief description: In the above given question we need to calculate values of all the DC parameters…

Q: Question #4 Consider the step response of a second order system to answer the following questions 1)…

Q: 2 a) 4.51 b) 6V @ 6₂ E + 0 1002 Mu I= ? ▷ I= ? R = loov for above Circuits: What is I when switch is…

A: We need to find out the current and power for given circuit

Q: Implement the following differential equation by using integrators based on Op- Amp. Where all…

Q: *9. For the network of Fig. 19.48: a. Find the average power delivered to each element. b. Find the…

A: As per our guidelines we are supposed to answer only 3 subparts of one question. Please repost the…

Q: Three unequal single-phase loads so connected in delta across the lines of a balanced, 3-phase, 230…

A: According to the given data, the circuit is drawn below

Q: Example13/ Find |Ed| at d=0, λλ 3λ λ 5λ 6λ σλ '8'4' 8 8 8 8 KR=1L 0° Draw standing wave pattern…

Q: Perform the following operations: Find the final value of X(s) = 5 3 S S+2

A: Given, The function is, Xs=5s-3s+2

Q: Question 4 (a) A magnetic circuit shown in Figure Q4.a. The mild steel core has a mean length of 50…

A: The given magnetic circuit is shown below. Relative permeability is μr=2500 AT/m at flux density of…

Q: Data suggest that undergraduate enrollment can be described by the equation: Qu = 25,000 - Pu where…

A: Given: Undergraduate enrollment : Qu = 25000 - Pu Graduate Enrollment : Qy = 13.500 -0.5Pg (a)…

Q: What are the properties of a circle D-mosfet in the subject of field effect transistor

A: Brief description: Here in the above question they want to know properties of depletion type of…

Q: V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of the circuit given…

Q: Q5. In the 3-phase system shown below, phase a is on no load and phases b and c are short circuited…

Q: Determine the voltage value in volts on voltage across the resistance of 2 ohms. 1Ω 12Ω 12 Ω 6A Μ 2Ω…

A: In this question we need to find a voltage across 2 ohm resistor.

Q: Open write T-L with L=30 m, ZR = Zo = 502, f=50 MHZ Find Z, and Za d = 10 m

Q: Q\ Compare between Permanent Magnet Synchronous motor and Reluctance motor and single phase…

A: Motor is nothing but machine which can take electrical energy as a input and the work as a output.…

Q: Q7: Plot the output Vo() of the following circuit. where Vcc=+_15V. 15V + 10sin(0) Vo (0) -15V CH2…

Q: For PAM signal calculate sampling frequency, pulse width, power of PAM signal at 1k ohm and draw…

A: Here we discuss about the power & the sampling frequency of the given PAM signal.

Q: calculate all the voltages and currents for each resistor.

Q: Mechatronics 9. A=0 B=1 C=1 D=1 A B X 10. A = 1 B = 0 C = 1 D = 1 E = 0 11. A = 1 B = 1 C = 1 D = 1…

Q: i. Write the unsimplified Boolean expression for the output Y. Simplified the above Boolean…

A: The Boolean expression can be obtained by evaluating the individual logic gate output and then the…

Q: 2.12 the circuit of Fig. 2.76, obtain U₁, U2, and V3. 15 V 25 V 13 20 V 10 V + VI

A: We need to find out the unknown voltage for given circuit

Q: 3. Describe types of Starters used in three phase induction motor and their Function.

A: There are several types of starter for three-phase induction motors, including star delta starters,…

Q: Refer to the figure below. A rectangular current loop, with dimensions a= 5cm and b=4cm, is pivoted…

A: Given, a=5cm, b =4cm I=2mA, and B=2ax T. Torque can be calculated as

Q: 2. Calculate all voltage drops and currents in this circuit, complete with arrows for current…

A: The required parameters can be calculated by using the ideal opamp characteristics and by using the…

Q: 1. Z parameters=? 492 392 a.)z11=7ohms,z12=z21=z22=3ohms b.) a.)z11=8ohms,z12=z21=z22=4ohms c.)…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source. Load 1: Inductive load, 125kVA,0.28PF lagging. Load 2: Capacitive load, 10kW,40kvar. Load 3: Resistive load, 15kW. (a) Determine the total kW, kvar, kva, and supply power factor. (b) In order to improve the power factor to 0.8 lagging. a capacitor of negligible resistance is connected in parallel with the above loads. Find the kvar rating of that capacitor and the capacitance in F. Comment on the magnitude of the supply current after adding the capacitor.
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
Three loads are connected in parallel across a single-phase source voltage of 240V(RMS). Load 1 absorbs 15 kW and 6.667 kvar; Load 2 absorbs 3 kVA at O.96PF leading; Load 3 absorbs 15 kW at unity power factor. Calculate the equivalent impedance, Z, for the three parallel loads, for two cases: (i) Series combination of R and X, and (ii) parallel combination of R and X.
A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the instantaneous source voltage. Also determine the phasor and instantaneous currents entering the positive terminal if the circuit element is (b) a 20 resistor. (C) a 10mH inductor, and (d) a capacitor with 25 reactance.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
The total instantaneous power delivered by a three-phase generator under balanced operating conditions is (a) A function of time (b) A constant
Three identical impedances Z=3030 are connected in to a balanced three-phase 208-V source by three identical line conductors with impedance ZL=(0.8+j0.6) per line. (a) Calculate the line-to-line voltage at the load terminals. (b) Repeat part (a) when a s-connected capacitor bank with reactance (j60) per phase is connected in parallel with the load.
Two balanced Y-connected loads in parallel, one drawing 15 kW at 0.6 power factor lagging andthe other drawing 10 kVA at 0.8 power factor leading, are supplied by a balanced, three-phase,480-volt source.a. Draw the power triangle for each load and for the combined load.b. Determine the power factor of the combined load and state whether lagging or leading.c. Determine the magnitude of the line current from the source.
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power
The load to the three phase supply comprises three similar coils connected in Star. The line current are 25Amperes and the KVA and KW inputs are 20 and 11 respectively. Find , The phase and line voltage, The KVAR input, The resistance and reactance of each coils.