Two resistance in parallel gives combine effect of 6/5 ohms. If one resistance broke, the effective resistance becomes 2ohms. The broken resistance will be_____?

Q: Describe  circuit's every working procedure and describe all equipment and function according to the…

A: Working procedure,equipment and function of OP275 Low pass filter design circuit:

Q: Any example traced in your reading material, connections between the current and the potential…

A: Correct option is c.

Q: A power line is to be run to an offshore facility where its 5 miles at sea and 2 miles along…

A: It is given that: a power line is to be run to an offshore facility where its 5 miles at sea and 2…

Q: e) PV cell is indirect method of solar energy (true or false)?

A:

Q: What is the number of basic nodes in the circuit given below?

A: In this question we need to find a number of basic nodes of the given circuit.

Q: What do call to the encircle part of socket and what is the purpose?

A: It is a 3 pin plug. There are three wires in a 3 pin plug named as- 1 – Earth -E 2 – Neutral -N 3 –…

Q: What spaces are not included in floor area when calculating the load in volt amperes per square…

A: For calculating the load, first evaluated the total floor area. And according to the NEC , the total…

Q: 5) The Murray Loop Test figuer shown below is used to locate ground fault in a telephone…

A: Solution- Murray loop test, R = R1+R2 = 600 Ω R3 = 2 kΩ  = 2000 Ω   R4 = 1 kΩ    R1 =RR3R3+R4 =…

Q: define the fake resistance

A: Fake resistance has property of some electrical circuit s and devices in which an increase in…

Q: Could several panels be placed in parallel in order to increase the power of the system? What…

A: Yes, if numerous panels are connected in parallel, the system's power is increased. When solar…

Q: A DC is supplied through a solid conductor cable. The fault in the cable can be determined by using…

A:

Q: 29: Suspension type insulators are used for voltages beyond

A: There are many type of insulators are available  strain type shackle type pin type suspension type

Q: Explain in paragraph the relationships of resistance, voltage and current, and the distribution of…

A: Question is asking about relationships of resistance, voltage and current  also distribution of…

Q: The solar energy captured by the plant while growing up

A: while growing up  the plant capture the solar energy

Q: 1. At which end of the. scale are resistance readings more reliable, the crowded or the uncrowded…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Describe the circuit's every working procedure and describe all equipment and function according to…

A: Working procedure,equipment and function of Over Heat detection circuit:

Q: A suspension string have 3 units. Voltage across topmost and lower most unit of string are 6.71…

A: Total string voltage = Sum of voltages across the each Unit. Given there are 3 units  and voltage…

Q: items that contribute to Earth Resistance for your grounding system and what can be done to minimize…

A:

Q: 2. An Electrical heating pad rated 110v and 55 W is to be used at a 110 Volt source. It is to be…

A: In this question 5 electric bulbs are connected in parallel....We have to find out current flowing…

Q: what are the ballast resistors used for?

A: when the current in the circuit increase above the predefined value, the value of the resistnae also…

Q: Draw equivalent circuit of PV cell with explanation and labelling in details

A: PV cell:  It stands for Photo voltaic cell . It is also called as solar cell. It is a device which…

Q: 1. At which end of the scale are resistance readings more reliable, the crowded or the uncrowded…

A: Resistance measurement is an important measurement that a multimeter may do. Not only may resistance…

Q: Hello sir , I want the solution in detail , with an explanation of each step , please .. Thanks for…

A:

Q: 5. One of electrical wiring design procedure is that circuit all and to the appropriate panels and…

A: Electrical wiring is a proper installation of cables, switchboard, sockets etc in a circuit. Steps…

Q: The need of using plenummed cabling in the space above the ceiling tile may be explained as follows

A:

Q: Using Superposition Method. Determine the voltages at the 5-ohm resistor due to the 24-Volt, 38-Volt…

A:

Q: Using the Mesh Current Method, what is the value of VA?

A:

Q: 5. The wiring diagram for a household floor lamp with three bulbs is shown below. Calculate the…

A: Step1 In this question, we have to find out current flow throgh each bulb. Assume that light bulbs…

Q: The device (or element) that used to protect electronic components which are vulnerable to reverse…

A: Device used for protection of electronic components which are vulnerable to reverse voltage is:

Q: This discussion relates to Bonding. Whys is bonding of the conduit necessary when using reducing…

A: Bonding becomes necessary to reduce the risk of shock and it also provides a low impedance path to…

Q: List the items that contribute to Earth Resistance for your grounding system and what can be done to…

A: List of the items which contribute to the earth resistance for the grounding system are named below:…

Q: a) In above circuit at which condition power exaction from solar PV system to load will be maximum?…

A: the condition for power excitation from solar PV system to load will be maximum

Q: What are the type of circuit breaker

A: There are mainly four types of circuit breakers  1. Air blast Circuit Breaker  2. SF6 circuit…

Q: What are unit system of protection

A: Switchgear protection :- It is very important for modern power system network. It protects system…

Q: A three pole contractor would allow how many paths for current allow ?

A: The path allowed for the passing of the current by the three pole contractor are four.

Q: What is the voltage and maximum current that can be used on the three cable types to power DeviceNet…

A: DeviceNet DeviceNet is a network protocol used in the automation sector to connect and share data…

Q: What is the name of the circuit given below?

A:

Q: iii. How much current will enter the branch BE?

A:

Q: How can the electrical hazards in number 3 be prevented?

A: The main electrical hazards that can occur while working with electricity are: electric shock and…

Q: Describe those circuit's every working procedure and describe all equipment and function according…

A: Over Heat detection circuit:

Q: How do I build this circuit?

A: Circuit elements of given circuit: PSB 5V D1 RED SW1 R1 330 ohm D2 BLUE SW2   We are required to…

Q: The voltage drop is as we proceed from the supply end to the consumer points

A: We know that the voltage at supply and will be maximum and as we go towards the consumer point it…

Q: Explain Wheatstone Bridge with necessary diagram and equations.

A: Figure of Wheat stone bridge:

Q: What are the resistance readings?

A:

Q: he unit of resistance is

A:

Q: What is the current flowing on the 9-ohm resistor if the source voltage is placed at 16 volts?…

A: In this question first we will find equivalent resistance across ab then total current and will find…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.