Two rods, A and B, of equal free length are elastic. Both hang vertically 0.6m apart and support a rigid bar horizontally. The bar remains horizontal when a vertical load of 60 KN is applied to the bar 0.2m from A. If the stress in A is 100 MPa, determine the stress in B and the cross-sectional areas of the two rods: E_{A} = 200GPa E_{B} = 130GPa

Two rods, A and B, of equal free length are elastic. Both hang vertically 0.6m apart and support a rigid bar horizontally. The bar remains horizontal when a vertical load of 60 KN is applied to the bar 0.2m from A. If the stress in A is 100 MPa, determine the stress in B and the cross-sectional areas of the two rods: E_{A} = 200GPa E_{B} = 130GPa

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the cross section of a short column. Knowing that y = 5 in., determine (a) the stress at point A, (b) the stress at point B, (c) the location of the neutral axis.
The split ring shown has an inner radius r1 = 0.6 in. and a circular cross section of diameter d = 0.8 in. Knowing that each of the 115-lb forces P is applied at the centroid of the cross section, determine the stress at point A and at point B.
Mechanics of Materials (Statically Indeterminate Members) A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown in the figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional areas of 190 mm2 and 290 mm2, respectively. A uniformly distributed load of w= 12 kN/m is applied on the rigid beam as shown in the figure. Assume L= 3 m, a= 1.7 m, length of rods= 2.1 m and E= 57 GPa. Determine the force in rod (1)? Determine the force in rod (2)? Determine the normal stress in rod (1)? Determine the strain in rod (1)? Determine the deformation in rod (1)? In mm Determine the deformation in rod (2)?in mm
A horizontal bar of negligible mass, hinged at A in FIGURE Z and assume rigid, is supported by a bronze rod 2 m long and a steel rod 1 m long. For the steel rod, the area is 600 mm², and E = 200 GPa. For the bronze rod, the area is 300 mm², and E = 83 GPa. Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b. 1.36 mm c. 2.56 mm d. 3.18 mm
The couple M is applied to a beam of the cross-section shown in a plane forming an angle β withthe vertical y-axis. Determine the total normal stress at point A, point B, point D.
d1=60 mm and d2 =36 mm .Determine stress in rod in AB and BC
A vertical force P of magnitude 20 kips is applied at point C located on the axis of symmetry of the cross section of a short column. Knowing that y = 5 in., determine (a) the stress at point A, (b) the stress at point B, (c) the location of the neutral axis. My question is why point B is under compression and point A is under tension?
Rigid bar ABC supports a weight of W = 171 kN. Bar ABC is pinned at A and supported at B by rod (1), which has a circular cross section. If the normal stress in rod (1) must be limited to 170 MPa, determine the minimum diameter required for the rod (in mm).
Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the ring at B, determine the angle ? so that the average normal stress in each rod is equivalent. What is this stress? (10)
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 9 ksi, Sy = 34 ksi, and Sxy = 12 ksi. (a) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point. (b) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)