Type of Transistor: ? Circuit J+ Input (vs): Terminal ? Output (vo): Terminal ? Type of Amplifier Configuration: Common-? Amplifier R; R. Cc2 Rs Ci ww RE Circuit Parameters Transistor Parameters RC Rs = 500 2 RB = 100 k B= 120 VBE(ON) = 0.7 V Vs RL RB VEE VcC RE = 12 k2 VT = 26 mV RC = 12 k2 VA = 0 + RL = 6 k2 VEE = +3.3 V Vcc = +3.3 V By stating and applying electrical circuit theory/law/principle: Sketch the small-signal (ac) equivalent circuit. Derive and Prove that the small-signal (ac) parameters: gm = 7.73 mA/V, ra= 15.5 k2, ro = 0, Ai = 0.654 and Av = 6.26 3. 4. 5. Derive and Prove that the input resistance and output resistance are Ri = 127 2 and Ro = 12 k2, respectively

Type of Transistor: ? Circuit J+ Input (vs): Terminal ? Output (vo): Terminal ? Type of Amplifier Configuration: Common-? Amplifier R; R. Cc2 Rs Ci ww RE Circuit Parameters Transistor Parameters RC Rs = 500 2 RB = 100 k B= 120 VBE(ON) = 0.7 V Vs RL RB VEE VcC RE = 12 k2 VT = 26 mV RC = 12 k2 VA = 0 + RL = 6 k2 VEE = +3.3 V Vcc = +3.3 V By stating and applying electrical circuit theory/law/principle: Sketch the small-signal (ac) equivalent circuit. Derive and Prove that the small-signal (ac) parameters: gm = 7.73 mA/V, ra= 15.5 k2, ro = 0, Ai = 0.654 and Av = 6.26 3. 4. 5. Derive and Prove that the input resistance and output resistance are Ri = 127 2 and Ro = 12 k2, respectively

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
A) What does VCO stand four? Show by drawing the relationship between its input and output signals. Compare VCO circuit with LC Tank circuit in terms of circuit functionality and how the output is generated in each of them. B) Compare between AM and FM in terms of noise immunity, interference, equipment complexity and cost and line of site transmission.
Explain deeply how Darlington- Voltage-Divider Amplifier with current mirror and the output phase is non-inverted works.
2. A load of 8Ω is supplied by a single-switch Direct Current (DC) chopper with an inputvoltage of 40V. The switching frequency is 800Hz, the duty ratio is 0.4, and thetransmission voltage drop of the transistor is 2.4V a. Draw the chopper circuit presented in the question b. Find the switching period with the duty time of BJT c. Draw the load voltage, load current, BJT current, BJT voltage along two periods d. Find the output voltage. Is the achieved load voltage the average value or the effectivevalue e. Find the output power f. Find the average value and effective value of BJT current g. Find the power loss of BJT h. Find the DC source current i. Find the circuit efficiency
During turn-on and turn-off of a power transistor, thecurrent-time and voltage-time relationships are asshown in the adjacent figure. Observe the waveformsand calculate,40) the OFF-state power dissipation (static);41) the switch ON-state power dissipation(static);42) the average switching loss for the OFFtransition (dynamic);43) the average switching loss for the ONtransition (dynamic);Assume a switching frequency of 2kHz with 397V as specified in Appendix A.
Topic: Input and Output Characteristics of Transistor in Common Base Configuration Answer in 2-3 sentences each. Need a kind tutor that will do it for me. Thank you! 1. What are the applications of the common base (CB) configuration? 2. What are the output and input impedances of CB configuration?
In the circuit given in the figure, R₁ = 850kQ, R₂ = 350kQ, Rs = 4kQ, RL = 4kQ,VDD = 10V, VSGQ = 2.084V and transistor parameters VTP = -1.2V,kp = 40μA/V², W/L = 80 andIt is given as λ= 0.05V-¹. a) Find the gm and ro small sign parameters of the transistor.b) Draw the small sign equivalent of the circuit. c) Find the low signal voltage gain of the circuit AV = V0/Vi.
Complete the diagram for an amplifier system below.
Topic: Field Effect Transistor For the given circuit, determine the parameters required in each below: a. Gate Voltage (VG) b. Drain Current (ID) c. Drain-Source Voltage (VDS) d. Gate-Source Voltage (VGS) e. Source Voltage (VS) f. What biasing method was utilized in the circuit? self bias, fixed bias, voltage divider bias, or source feedback bias?
According to the digital circuit given in the figure, which option is correct for X and Y shown as outputs?
Topic: Field Effect Transistor Given the FET Amplifier circuit. Answer the question asked in each letter. a. Transconductance Gain (gm) b. Drain Resistor (RD) c. Input Impedance (Zi) d. Output Impedance (Zo) e. Voltage Gain (Av) f. What is the AC configuration of the amplifier?common source, common gate, common drain, or source bias?
Subject : Electronics Engineering How the transistor can be used as an amplifier in CE configuration? Explain with proper diagram.