Find the discharge over the rectangular sharp crested weir shown in the photo O Cengage Learning 201499O A tank measuring 10.0 feet by 10.0 feet by 0.0 feet is completely filled withwater If a 4-inch-diameter, square-edged orifice is located 1.00 foot abovethe bottom of the tank (to the orifice center), (a) What is the discharge?(b) Estimate the time required to empty the tank halfway.9. Find the discharge over a 90-degree V-notch weir if the head is 7.5 inches10. Find the discharge over a 60-degree V-notch weir if the head is 6.25 inches11. Find the discharge over the rectangular, sharp-crested weir shown below.00.0Weir crestChannel invert4.00'0.55'2.00'1.25'6.00'10.ow

Answered: Image /qna-images/answer/7477ff45-a204-488e-aeed-c9abbe800604.jpg

Answered: U.2J IMChes. 11. Find the discharge…

U.2J IMChes. 11. Find the discharge over the rectangular, sharp-crested weir shown below. Weir crest Channel invert 4.00' 0.55 2.00' 1.25' 6.00'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: b) An open channel has the croOss-sectional shape as shown in Figure 2 below. The main and side…

Q: The discharge over a trapezoidal weir is 1.315m³/s. The crest is 2m and the sides are inclined at…

Q: A right-angled triangular channel carries a flow of 16,000 l/s. The Manning's n = 0.020 and the…

Q: channel width = 4 m depth of water= 1.2 m flow of water = 3.6 m^3/s C = 0.58 Determine the…

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a 90-degree triangular…

A: Given:- A 90 degree triangular weir Head over the weir = 0.30 m To find:- Discharge in L/s

Q: 9. In discharge of water over narrow crested weir, discharge is directly proportional to the second…

A: formula for discharge over narrow crested weir Q=23Cd2gLH32

Q: Determine the discharge of water over a 90° V-notch weir under a head of 0.63m.

A: Given,headH=0.63 mangleθ=90°we know that,Discharge through a 90° V-notch weirQ=815CD2gtanθ2H52take…

Q: B- For the Given canal section the sides of canal tilted at un angle 30" with the horizontal…

Q: PROBLEM 2: Compute the flow rate over each weir. Assume Cd-0.60 1 ft 0.5 ft 60° weir plate 95cm 75cm…

A: GIVEN DATA:-⇒Cd=0.60⇒θ=60°→Formulae Used:-(1) Flow rate for triangular weir is given by:-⇒…

Q: 6. Determine the discharges in channels having the following sections for y ft, n = 0.015, and S =…

A: please find attached solution below. please repost 4th part of question.

Q: Determine the discharges in channels having the following sections for y = 6 ft, n = 0.015, and S =…

Q: ermine the head (in meters) on a 35° V-notch weir for a discharge of 405 L/s. Use Cd = 0.948. Round…

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a 90-degree triangular…

Q: A rectangular contracted weir 3m long is built in the left end of a rectangular channel 6m wide. How…

Q: Compute the discharge in m3/s of a suppressed rectangular weir, C = 0.60, L = 4.88 m, H = 1.1 m %3D…

A: As per Bartleby policy we are supposed to solve only first question for multiple question…

Q: Determine the discharge in lit/sec, of the weir having a head of 0.3 m. a) If a 90° triangular weir…

A: To find out the discharge in L /s when :- a) If a 90° triangular weir is used. b) If a trapezoidal…

Q: Find the normal depth for a discharge of 350cfs in a rectangular channel with a bottom widith of 20…

Q: End View Water Flow H B H= head or height of water the weir P= height of weir from bottom of channel…

Q: Design a vertical drop to change the upstream to downstream water levels by 2m. Assume the same…

A: Q = 3m3secy = 1.71mV = .43msecB = 1.5mz = 1.5m

Q: Find the water depth just upstream of a 4-ft-high broad-crested weir in a channel 10 ft wide when…

A: Given: The upstream depth is 4 ft. The width of the channel is 10ft. The flow rate is 51.14 cfs.

Q: H.W. : Aboard crested is constructed across channel if which the discharge is (30cumces) the cross…

A: Given Discharge through the weir, Q = 30 m3 Area of the weir, A =35 m2 Head of weir at crest, h =2…

Q: The discharge from a six (6) inch diameter orifice, under a 10 ft head, Cd=0.600, flows into a…

A: GIven Data:- Diameter of Orficed=6 inch Head available H = 10ft Coefficient of dischargeCd = 0.6…

Q: in the both end rectangular contracted weir, the length of the w neglecting velocity of approach and…

Q: Determine the discharge (ft3/s) of the weir having a head of 3.84 ft. if it is a triangular weir…

A: Given:- Head of the weir = 3.84 ft The central angle of the triangular weir = 69° Cc = 0.898, Cd =…

Q: A rectangular weir is designed to span the full width of a rectangular channel with B=L=2.5 m.…

A: Given, L = B = 2.5 m Q = 0.405 m3/s Cd = 0.625

Q: Determine the head on a 45° V-notch weir for a discharge of 200 L/s. Use C=0.57.

Q: Determine the head (in meters) on a 49° V-notch weir for a discharge of 427 L/s. Use Cd = 0.946.…

Q: 5. An Ogee weir 5 m long had a head of 40 cm of water. If CD = 0.61, find the discharge over

Q: 5. Determine the backwater profile created by an obstruction in a channel causing a backup of 5.0…

A: step 1-

Q: A trapezoidal weir has its non-parallel sides inclined at 4V:1H. It has a base of 4.54 m. and a head…

Q: A rectangular channel 4m wide with critical depth of 2.5 m. Compute the: a.) Discharge b.) Froude…

Q: An unsymmetrical triangular weir with a vertex angle equal to a = 38 deg(left half) + B = 31…

Q: 6. The height of water on upstream and downstream side of a submerged weir of 4 m length are 24 cm…

A: Given The height of water on the upstream and downstream sides of a submerged weir of 4 m length are…

Q: 3. Find the width (m) of the channel at the back of a suppressed weir with head equal to 28.5cm,…

A: Given data, Discharge = 0.84 m³/s H = 28.5 cm Depth of water = 2.485 m To find out the width of…

Q: A doubly-contracted weir, 1.25 m high, is to be installed in a channel 2.5 m wide. The maximum flow…

Q: the crest if the sides are inclined 75'57'50" with the horizontal. The discharge over a trapezoidal…

A: Given: Q= 1.315 m3/s, L = 2m, Inclination = 75 deg 57 min 50 sec

Q: A suppressed weir is located at the end of a square tank (s = 3.05m) and height h = 10m. If the…

Q: Design a semi-circular open channel (n=0.014) that is anticipated to convey 20cumecs of water. The…

Q: angular weir with a vertex angle equal to α = 40 deg(left half) + β = 26 deg(right half). What is…

Q: a rectangulsr suppressed weir is placed on the side of a reservoir whose plan area is a constant…

A: step 1-

Q: A trapezoidal weir having side slope of 1H to 2V discharges 50 m3/s under a constant head of 2m.…

A: given data: head (H)= 2m discharge (Q)= 50 m3/s C=0.60

Q: A 119-degree V-notch-weir was installed to measure the flow in an artificial channel. The crest of…

Q: H.W. : Aboard crested is constructed across channel if which the discharge is (30cumces) the cross…

Q: Find the discharge over the 90-degree V-notch weir if the head is 8 inche a. 0.6 cfs b. 0.7 cfs 0.8…

A: Given data : Head (h)=8 inchesAssume Discharge coefficient (Cd)=0.6Angle of V notch (θ)=90∘

Q: Q 2. Design an unlined trapezoidal canal cross section to carry a discharge of 1 cumecs on a…

A: Solution

Q: a rectangular suppressed weir is placed on the side of a reservoir whose plan area is a constant…

A: step 1-

Q: Determine the discharge (L/s) at the weir having a head of 0.813 m. if it is a trapezoidal weir with…

A: Trapezoidal weir H= 0.813m Theta/2 = 14.94 degree L = 5.38in= 0.1391m Cd1 = 0.661 & Cd2 =…

Q: how high (ft) is the flow above the crest of a 39 degree v-notch weir when the discharge is 19,514…

Q: Design a semi-circular open channel (n=0.014) that is anticipated to convey 20cumecs of water. The…

A: Given data: Q= 20cumecs slope of the channel bed = 0.0015 n=0.014 It is asked to design the…

Q: In a roctangular channel with 2m width 2. A hydrauic jump 15 occuring Flowrate and depth of water at…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Find the discharge over the rectangular sharp crested weir shown in the photo

O Cengage Learning 2014
99
O A tank measuring 10.0 feet by 10.0 feet by 0.0 feet is completely filled with
water If a 4-inch-diameter, square-edged orifice is located 1.00 foot above
the bottom of the tank (to the orifice center), (a) What is the discharge?
(b) Estimate the time required to empty the tank halfway.
9. Find the discharge over a 90-degree V-notch weir if the head is 7.5 inches
10. Find the discharge over a 60-degree V-notch weir if the head is 6.25 inches
11. Find the discharge over the rectangular, sharp-crested weir shown below.
00.0
Weir crest
Channel invert
4.00'
0.55'
2.00'
1.25'
6.00'
10.
ow

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A.Determine the velocity of flow in the pipe in fps. (Please round-off final answers to the nearest whole number) * B.Determine the discharge Q in ft^3/s. (Please round-off final answers to the nearest whole number) * C.How many feet above the center of the pipe will water stand in piezometer tube 3? (Please round-off final answers to the nearest whole number) D.How many feet above the center of the pipe will water stand in piezometer tube 4? (Please round-off final answers to the nearest whole number) *
An orifice at the bottom of a rectangular tank has a cross-sectional area of 0.004m². The tank has a cross-section of 3m x 2m. a. If it takes 2078 sec. to empty the tank if it contains water at a depth of 5.6m, find the coefficient of discharge. b. Compute the time to lower the water surface from 5.6m to 3m using C = 0.62.
A tank 20 ft long and 10 ft deep is 18 ft wide at the top and 8 ft wide at the bottom. In the bottom is an orifice having an area of 24 sq. in. and a coefficient of discharge of 0.60. If the tank is full of water at the beginning, how long will it take to lower the water surface by 6 ft? Ans: 14¼ min. Please draw illustration and label the notations used in your solution
Determine the amount of water that can be delivered by a sprinkler head having a 3/4" in orifice with a 13.7 k-factor and installed in an automatic sprinkler system having a 35 psi residual pressure.
A water tank is 30 ft in diameter and the normal depth is 25 t. The outlet is a 3-in horizontal pipe at the bottom a if this pipe is sheared off close to the tank, what is the initial flow rate of water from the tank? (Neglect hiction less stub of pipe) How long will it take for the tank to be empty?
Water flows from one tank to an adjacent tank through a 60-mm sharp-edged orifice. The head of water on one side of the orifice is 2.9 m and that on the other is 0.7 m. Assuming Cc = 0.63 and Cv = 0.96, calculate the flow rate
A venturi meter of 150 × 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5 cm of mercury (vacuum). -Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. choices: a.) 0.088 m^3/s b.) 0.345 m^3/s c.) 0.197 m^3/s d.) 0.441 m^3/s STRICTLY SHOW COMPLETE FBD need asap
A homeowner is interested in supplying water (at 20 °C) to her one-story house that is 5 m above the elevationof the water main. However, she is concerned about lack of water pressure. She hired you as an engineer todetermine if there will be sufficient pressure to supply the house at flow rate of 10 L/min through a 1.5 cmcopper pipe. The pressure at the water main is 70 psi and according to the plumbing code, flush valves require25 psi, regular water fixtures require 15 psi, and showers require 15 psi.
The sluice gate shown is in a channel that is 4 feet wide. The depth of y, is 6 feet and the depth of y, is 1 feet. Assume no loss of energy. a. What are the velocities V, and V, (in ft/s)? b. What is the discharge Q (in cfs)?
You are the engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe? In the piping system above, what is the uncertainty in computed head loss contributed by the velocity of the pipe? what is the uncertainty in computed head loss contributed by the diameter/s of the pipe? what is the uncertainty in computed head loss contributed by the length of the pipe? With all the above uncertainties, what is the total uncertainty in the head loss?
Show all problem solution's steps. Direct formula substitution solutions will have NO CREDIT POINTS. A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 25% of the velocity head in the jet. If the pressure at the base of the nozzle is 625 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet at a point two-third of the maximum vertical reach from the tip of the nozzle. Neglect air resistance.
A. Assuming sea water to be incompressible with a specific weight of 64.0 lb ft-3. what is the pressure in tons per square foot 2 miles below the surface of the ocean?B. A 40-mm-diameter circular pipe carries water at 20°C. Calculate the largest flow rate for which laminar flow can be expected (in m3 sec-1).