Use A36 steel and select the lightest American Standard Channel for a tension member that will safely support a service dead load of 444.82 kN and service live load of 222.41 kN. The member is 6.1 m long, and it is connected through the web with two lines of 25 mm diameter bolts. The length of the connection is 150mm. a. Use LRFD b. Use ASD

Use A36 steel and select the lightest American Standard Channel for a tension member that will safely support a service dead load of 444.82 kN and service live load of 222.41 kN. The member is 6.1 m long, and it is connected through the web with two lines of 25 mm diameter bolts. The length of the connection is 150mm. a. Use LRFD b. Use ASD

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.7P

See similar textbooks

Similar questions

f. Calculate the maximum safe load "P" in KN Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure shown below. Thediameter of the rivet is 20mm and the angles are each 100mm x 100mm x 12mm thick. For each bolt, assume thatthe allowable bearing stress is 220 MPa. Determine the allowable load P in KN on the connection. *show all theload P in kN for bearing stressBeam web thickness = 5mmGirder web thickness =
Select a rectangular (not square) HSS for use as a 15-foot-long compression member that must resist a service dead load of 35 kips and a service live load of 80 kips. The member will be pinned at each end, with additional support in the weak direction at midheight. Use A500 Grade C steel. a. Use LRFD. b. Use ASD
The steel is supported by the steel tie rod in AB beam B. Steel connection tension rod is placed 2 meters to the left of B and C sliding bracket is placed and P is loaded between AC It is. By ignoring the weights of beams and connecting rods, they can be determine the largest P load it can carry. The diameter of the BD rod is 16 mm. E = 200GPa I = 150x(10^6)mm^4
Ex: For a cantilever beam of length (L) subject 1 a concentrated load (P), shown in fgure, Find - 1 Max.tension and compression bending stress in beam section 2. Determine the proper spacing of the nails used 10 fix the flange boards to the web. The nals o be used can safely resist (F) of shearing force, given in 3 - “Table below. I»
A plate 1⁄2 3 4 of A36 steel is used as a tension member to carry a service dead load of 6 kips and a service live load of 18 kips. It is to be attached to a 3⁄8-inch gusset plate, as shown in Figure. Design a welded connection.
For the clevis connection shown, determine the shear stress in the 20-mm-diameter bolt for an applied load of P = 130 kN.
a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.
A double channel shape is used as a tension member. The channels are bolted to a gusset plate with 22mm diameter bolts. Fy-channel = 345 MPa, Fu-channel = 450 MPa Fy-plate = 248 MPa, Fu-plate = 400 MPa Achannel = 3555 mm^2, tw = 12.18 mm, Shear lag factor = 0.90 D. Determine the allowable tensile strength of the tension member based on its net area.
A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.The member is to be 15m long. Take R= 433.5 Factored design load= R*4
A double channel shape is used as a tension member. The channels are bolted to a gusset plate with 22mm diameter bolts. Fy-channel = 345 MPa, Fu-channel = 450 MPa Fy-plate = 248 MPa, Fu-plate = 400 MPa Achannel = 3555 mm^2, tw = 12.18 mm, Shear lag factor = 0.90 B. Determine the allowable tensile strength of the tension member based on its gross area.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. 1.Determine the maximum flexural stress experienced by the beam in MPa.2. Determine the maximum shearing stress in MPa at Neutral Axis.3. Determine the spacing of rivets in mm.