Use methods of section for members BD, CD, and CE

Q: Need part d asap Thanks!

A: Given data: Tm,i=20°Cp=1 atmd=25 mml=1.5 mm˙=6×10-4 kg/s Need to determine Reynolds number, rate of…

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: travelling ke to stop with W1 WI ning

A:

Q: a. Grashof count and Reynold count O b. Grashof number and Prandtl number c. Grashof number, Prandtl…

A:

Q: Identify any one application and draw a neat diagram for compressed air distribution system Note:…

A: Compressed Air Distribution System Compressed air distribution has the task of delivering compressed…

Q: I need the answer quickly  Orthographic view

A:

Q: Describe briefly please

A: Given data; In a single degree of freedom underdamped spring -mass-damper system as shown in…

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: 1 to one module.

A:

Q: يمكننا إدخال رقم صفحة من خالل 0 0 ( Footer Both Header and Footer > Header None of the above > O

A: In the Microsoft we can enter page number in the footer. Header

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: In the TRIM command, when selecting objects to trim, holding downthe <Shift> key: a. Allows…

A: By holding the <Shift> key while using the TRIM command, it will be inverted to the opposite…

Q: term gB(T - To) represents

A: Given: 2-D momentum equation for natural convection over a surface immersed in a quiescent fluid at…

Q: e cofactor of the el

A: To find  Cofactor of element zero

Q: Using Autocad 3d image Save as (*.dwg) Unit = inches

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Using the Unit Load Method

A:

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a…

Q: Choose the assumption made for using this FBD.

A: (ii) Answer = (a) explanation = for the FBD of the crate, the assumption that has to be made is that…

Q: er notation from the options provided. [Select] ed to be on top of each number. [Select] J Nim -IN…

A:

Q: State four espect to consider before selecting correct solvant

A:

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: Sketch the Orthographic and  auxiliary view

A:

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: Draw the FBD All distributed loads should be simplified to their equivalent loads Draw the FBD…

A:

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: (a) the melting temperature for ic

A: the melting temperate of ice at 0.01 atm = 10C Boiling temperature of ice at 0.01 atm = 7 0C

Q: An 'angle plate' is used to A. Hold a workpiece B. Mark various angles on the workpiece and hence…

A: An angle plate is a work holding device used as a fixture in metalworking.

Q: Gas welding process creates a messy work piece. Select one: True False

A: True In gas welding process oxy acetylene gas combustion take place and heat produced is utilised…

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: ee A. Positive, Negative C. Positive, Positive B. Negative, Positive D. Negative, Negative

A: This concept is based on the knowledge of thermodynamics.

Q: Sir Lost-a-Lot d

A:

Q: By using AutoCAD command draw the following samples with possible fitting. 1- Main door 2- Boiler 3-…

A: Given question: By using AutoCAD commands draw the following : 1. Main Door 2. Boiler 3.…

Q: Subparts 1, 2, and 3.

A:

Q: 2 kip/ft 50 kip - ft 50 kip · ft B 10 ft 20 ft 10 ft

A:

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: 1. Write the procedure for shaper process.

A: Shaper process is the process in which unwanted metal surface is removed by a single-point cutting…

Q: 3. Provide at least two distinctive definitions of two of the following terms:

A: Given Data : Job satisfaction leadership

Q: q4 part a plz provide handwritten answer asap

A: u asked only a part only so answer in hand written

Q: The tabulating machine which uses punch cards during 1890AD is ____? a) Pascaline b) Difference…

A: Data cards, commonly known as punch cards, are used to convey information to machines.

Q: Mechanical working of metal is another name for O a. Casting process O b. Machining process O c.…

A: Mechanical working is forming process .. there are two types of working cold and hot working.

Q: nsity withir WIT

A: Multiple options are given and we have to select the correct answer

Q: want orthographic view of both

A:

Q: Fill in the blank which is given below If 2 links are connected at the same joint, the joint is…

A: when x number of links are connected to the same joint then the binary joint formed is x-1 binary…

Q: Load 1. TV NOOT

A:

Q: Part A Determine the cutoff ratio. i Save for Later Attempts: 0 of 1 used Submit Answer Part B The…

A:

Q: With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5…

A: The free-body diagram of the junction of the boom, given load, and the force exerted by the cable,…

Q: Write a brief introduction about control of furnace door (OPEN ENDED) . Note:Include all the…

A: Given: There are automatic door of the furnace and automatic supplier of the fuel to the furnace. In…

Q: the principle orthographic views

A: The given object:                                      We have to draw the principle orthographic…

Q: sketch the B.M and S.F diagrams with indicating all

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.