Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1011 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z. S4 S1 S2 S3 0.

Q: Use the following state diagram and create the state table for a synchronous to detect the sequence.…

A: Given:

Q: Use the following state diagram and create the state table for a synchronous to detect the sequence.…

A: I have created state table and find equations for all states in step 2.

Q: Use the following state diagram and create the state table for a synchronous to detect the sequence.…

A: I have created state table and find equations for all states in step 2.

Q: 1. Design the state diagram and create the state table for a synchronous to detect the sequence…

A: GIVEN:

Q: The given State Diagram represents a circuit that has two Flip-Flops (A and B), one input (X) and…

A: Given: The above diagram represents a circuit that has two Flip-Flops (A and B), one input (X) and…

Q: 1. In the following sequential circuit. There are 2 D FF (A and B), 2 inputs (x and y), and 1 output…

A:

Q: 1. Design the state diagram and create the state table for a synchronous to detect the sequence…

A: A state diagram is composed of finite number of states and describe the behavior of systems.

Q: Consider the following sequential circuit that has two flip-flops A and B and one input x. It…

A:

Q: 1- In the following sequential circuit. There are 2 D FF (A and B), 2 inputs (x and y), and 1 output…

A: In order to make the state diagram we need the state table. We will create te state table according…

Q: Create a TRUTH TABLE, and draw the equivalent LOGIC DIAGRAM and TIMING DIAGRAM of the following…

A: For F = [p(qr'+q'r)s']' We have four inputs p, q, r, s and the output is F. The TRUTH TABLE for this…

Q: 4. Complete the state table from the following state diagram, write the functions using K-maps and…

A: The answer is given below:-

Q: Write the Boolean expression (in Sum of Products form) for the logic circuit that will have a 1…

A: For 3 -bit input number, there are total,  23=8 output states that will present in the truth table.…

Q: Write the Boolean expression (in Sum of Products form) for the logic circuit that will have a 1…

A: answer and logic diagram of the circuit has been mentioned in step 2.

Q: نقطة واحدة A combinational logic circuit has one output (F) and four inputs (a, b, c, and d). The…

A: Answer: I have given answer in the brief explanation.

Q: A sequential circuit with two D flip-flops, A and B; two inputs, x and y; and one output, z, is…

A:

Q: The following circuit implements a state machine. Obtain its state table and state diagram. (You…

A:

Q: Task In your group, design and simulate a combinational logic circuit that consists of three or four…

A: Actually, flip-flop is nothing but a  circuit.

Q: Task In your group, design and simulate a combinational logic circuit that consists of three or four…

A: Actually, flip-flop is a circuit.

Q: A sequential circuit has two D flip-flops, two inputs x and y, and one output Z is specified by the…

A: Lets see the solution.

Q: A sequential circuit with two D flip-flops, A and B; two inputs, x and y; and one output, Z, is…

A: a) The logic diagram of the circuit is given by:

Q: sequential circuit with two D flip-flops A and B, one input x , and one output z is specified by the…

A: The logic diagram is as follows,

Q: Consider the following sequential circuit that has two flip-flops A and B and one input x. It…

A: GIVEN:

Q: Design the transition logic using One FF per state method for the following state diagram, use logic…

A:

Q: A sequential circuit with two D flip flops A and B, two inputs x and y and one output z is specified…

A: D flip flop means delay flip flop which provide delay for some time and give output same as input.…

Q: The table below describes a synchronous sequential circuit constructed using 2 D-flip-flops where X…

A: A)  Input to flip flop is same as output of flip flop since the flip flop used is D.  Thus  next…

Q: A sequential circuit with two D flip flops, A and B; two inputs, x and y; and one output, z, is…

A: Logic Diagram:This is a graphical representation of a logic circuit that shows the wiring and…

Q: 4. Complete the state table from the following state diagram, write the functions using K-maps and…

A: The answer is given below:-

Q: (a) Draw a logic circuit for the case where the output, ENABLE, is HIGH only if the inputs, ASSERT…

A: Given:   a) Draw a logic circuit for the case where the output, ENABLE, is HIGH only if the inputs,…

Q: A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The…

A: Given Data:

Q: Analyse the sequential circuit shown in Figure 1 which has 2 rising edge-triggered flip-flops A and…

A:

Q: For of the following state functions:   Derive the state table.   Draw the circuit diagram.  …

A:

Q: Q1: For the state diagram shown below write the state table and design logic circuit 10 START FIRST…

A: Step 1

Q: QUESTION 4 a) Determine the suitable decoder based on the provided Boolean Expression and the truth…

A: a. Decoder circuit Expression:  K(A,B,C)=(1,2,4,7)

Q: Figure shows the diagram for an automobile alarm circuit used to indicate the status of the door,…

A:

Q: A combinational circuit with four inputs (A,B,C,D) and one output (Z) is designed as follows using…

A:

Q: Draw the truth tables for the following Boolean expressions. xy+yz+xz x¯y+yz¯+x¯z…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A combinational circuit with four inputs (A, B,C,D) and one output (Z) is designed as follows using…

A: Multiplexer: A multiplexer is a circuit with 2n data inputs, n selection lines, and a single output…

Q: The state table shown in Table 3 is for a sequential synchronous circuit. Choose a specific encoding…

A:

Q: A combinational logic circuit has one output (F) and four inputs (a, b, c, and d). The circuit is…

A: Lets see the solution in the next steps

Q: A combinational circuit with four inputs (A, B, C, D) and one output (Z) is designed as follows…

A:

Q: Find an appropriate state assignment by using the the smallest possible number of states and derive…

A: Solution ::  Let's first see that what is transition table ? and what is k-map ? This two we will…

Q: Consider the below sequential circuit to determine the values of L, M, N, Q in the corresponding…

A: Lets see the solution.

Q: 1- In the following sequential circuit. There are 2 D FF (A and B), 2 inputs (x and y), and 1 output…

A: Circuit Diagram for the above scenario

Q: Q3(A):For the state diagram shown below write the state table and design logic circuit 0/0 001 0/0…

A: Given state diagram contains,  Set of states={000, 001,010,011,100} Set of input alphabets={0, 1}…

Q: Question 1 Consider the following logic circuit. B OD a) Write the Boolean function F (A, B, C). b)…

A:

Q: Design a sequential circuit with two T Flip Flops, A and B, and two inputs, E and x. If E=0, the…

A: Answer :

Q: ne figure below shows the state diagram of a synchronous circuit to detect e sequence 101. The…

A:

Q: Design a combinational circuit with three inputs x, y, and z and three outputs A, B, and C. When the…

A: Draw the state table of the inputs x, y, and z and three output A, B, and C as follows:

Q: A staircase light is controlled by two switches, one is at the top of the stairs and the other at…

A: Question :-

Q: A staircase light is controlled by two switches, one is at the top of the stairs and the other at…

A: Question :-