Use the method of Joints to determine the forces in AC CD, BF, EF member and state whether the member is in tension or compression. -Use the method of Sections to determine the force members DG, DM, LM, and state if the members are in tension or compression. Determine the all the zero-force members. 2kN

Use the method of Joints to determine the forces in AC CD, BF, EF member and state whether the member is in tension or compression. -Use the method of Sections to determine the force members DG, DM, LM, and state if the members are in tension or compression. Determine the all the zero-force members. 2kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.18 Determine the truss's smallest safe cross-sectional areas of member's CD. Ch. and GF. In tension, the working stresses are 140 MPa, while in compression, the are 100 MPa. (In compression, the working stress is smaller to reduce the risk of buckling.) B D. 311 3n 2n 2ft 3ft H 3ft G 3t 3t 120KN 120KN V
Question 1: A-find the zero force members of the truss shown below. B-Using section method determine the force in member HG, BG and BC, indicate whether tension or compression. 1 m 2m -2 m- H 16 B C -2 m--2 m--2 m- 10 kN E
Usinf the method of sections, determine the force members GF, GD, and GC
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression.
Problem 5-4 A 300 lb 30° 12'-0" B D 600 lb 30° 12'-0" C 1 Calculate the forces in all members of the truss shown using method of joints...
This truss contains diagonals that are not slender. F E D 3m 4 m- 4 m 10 kN 20 kN 10 kN Determine the forces in members AE, BE, FB in kN. (don't forget that compression is negative, "-") And what is the equation used to calculate truss degree of indeterminacy? j-r 3r - b (ktt) - 2j (bti) - 2r
2: Determine the suppont reactions at A and F Using the Method af joints, find the forces in the fallowing members; e AB, GH and ED . Using the method of sections, find the forces in fhe folloning members : HD, Co and BC. [clearly show all calulations and peseut falle your Final auswers in a teste 5 kN 16시 3m 20 KN 4m 4m 4m 4m 4m
Given truss shown, P 50 kN. The tensile oallow 140 MPa, and the compressive Oallow = -85 MPa. If the truss is to support a maximum load P (as given). shear, pin at B is in single shear %3D = 140 MPa, pin at A is in double allow Determine the required Area of the members AB, BC and AC if the Oallowable of the members is 135 MPa. - 450 mm→ B (3) 600 mm (1) 1200 mm
Determine the smallest allowable cross-sectional areas of members BD, BE, and CE of the truss shown. The working stresses are 200 MPa in tension and 120 MPa in compression. В 6 m 4 m A C E F 4 m 4 m 4 m 36 kN
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)