Jsing 1s Angle Projection, draw the following views for the part shown in below (dimensions need to e placed on the drawing): 1- Top View 2- Front View 3- Side View Dimensions are shown in mm. 42 20 80 20 02

Q: Refer to the four bar mechanism shown in figure. AB = 40 cm, BC = 50 cm. DC = 30 cm. AD = 20 cm. At ...

A:

Q: An orificemeter with orifice diameter 10 cm is inserted in a pipe of 20 cm diameter. The pressure ga...

A: To Find: Discharge of water through pipe, Q Given that, d0=10 cm=0.1 m(orifice),d1=20 cm=0.2 m (pipe...

Q: D.I 4.5-8. Consider the following problem. Maximize Z = 50x1 + 25x2 + 20x3 + 40x4, subject to 2x1 + ...

A:

Q: A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of...

A:

Q: a. State the enthalpies at each point: enthalpy Point kJ/kg kJ/kg h kJ/kg h2 kJ/kg h3 kJ/kg h4

A: Given that: Condensing pressure = 1400 kPa Evaporating temperature = -20 oC Exit of the evaporator h...

Q: The space truss supports a force F = {600 i + 450j-750 k} lb. (Figure 1) %3D

A:

Q: 5.15 The flow and head requirements for a particular application are 20 cfs and 100 ft., respectivel...

A: Given : Q = 20 cfs = 9000 gpm H = 100 ft N = 1750 rpm To find : Specific speed if connected in serie...

Q: Give 2 types of refrigirator system that can be used for mini portable refrigirators or cooler box ,...

A:

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at des...

A:

Q: The following principle is taken from Abeles (Ref. 2.32) and applicable not only to prestressing con...

A: Although a San Francisco engineer developed prestressed concrete in 1886, it was not widely used as ...

Q: Water (3 m/s, 1 cp, 900 kg/m3) flows inside a rectangular duct of sides 3 cm and 2 cm. Calculate the...

A:

Q: Solve the following: 1 1- lim r-1 In r Answer =1/2 2-lim Vx +6x -x ? Answer =3 - TTX 3- lim(tan - ?=...

A: 1. Given: The function, y=limr→1rr-1-1lnr

Q: Problem 2-55. If F: = 150 lb and 0 = 55°, determine the magnitude and direction measured clockwise f...

A:

Q: Problem 3: Octane flows steadily through the duct shown at a rate of Q = [0.2 + 0.001(M+ D) m'/s. Th...

A: Given data, Flow rate of octane is Q=0.2+0.001M+DQ=0.2+0.0018+10Q=0.218 m3/s Length of the duct, L =...

Q: The assembly in the depicted image below consists of a light rigid bar AB, pinned at O, that is atta...

A:

Q: Imagine we are viewing the pipe from an Eulerian perspective. The pipe is heated with a Bunsen burne...

A:

Q: A flat rectangular plate 1 m wide and 2 m iong is immersed in water. The shorter side parallel to wa...

A:

Q: The following data are obtained from a tensile test of a copper specimen. - The load at the yield po...

A: It is required to determine final area of specimen

Q: A steel pipe of 2.0 in (nominal diameter) carries steam at 150°C. It is coated with ½ in of mineral ...

A:

Q: r half and is acted on by the upp its strength, it will break. The tw of the tensions in BD and CD, ...

A: solution of above problem is below:  

Q: Situation - An eccentrically loaded bolted connection is shown in the figure below. Diameter of A325...

A:

Q: most essential parts of the lathe for it to function

A: Most essential parts of lathe.

Q: Name at least two units that you use every day.

A: Most of the time in the day to day life there are many duties which have to be done daily y u. Some ...

Q: Explain the "burst potatoes in the boiling water" with thermodynamic viewpoint.

A: Whenever potatoes are boiled in the water, there is heat transfer from the hot water to the potato. ...

Q: 2. A long measuring stick rests against the wall in a physics laboratory with its 200-cm end at the ...

A: Given data The length of measuring stick = 200 cmIt lands on the 100 cm markIts movements are as fol...

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: A 250 mm diameter circle is etched on a 400 mm x 400 mm x 12 mm piece of sheet metal. The elastic mo...

A: Solution: Given Data: d = 250 mm E=190 GPav=0.3σx=40 MPaσy=75 MPat=12 mm

Q: Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = ...

A:

Q: A jet of water from a fixed nozzle has a diameter of 25 mm and strikes a flat plate at an angle of 3...

A: We know that a fixed nozzle's water jet has a diameter of 25 mm and impacts a flat plate at a 30o an...

Q: 4.123 A rigid, insulated tank having a volume of 40 ft° initially contains a two-phase liquid-vapor ...

A:

Q: The steel strip has a unifom thickness of 50 mm. Compute the elongation of the strip caused by the 5...

A: GIVEN DATA- a=120mm b=50mm t=50mm P=500KN L=1000mm E=200GPa WE HAVE TO FIND TOTAL ELONGATION

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: Given: The maximum pressure is Ph=35 bar and lower pressure is Pl=0.4 bar. The pressure correspond...

Q: Determine the maximum tensile stress (MPa) at

A: Determine maximum tensile stress.

Q: 2. A medium size power station is used to produce 30 MW net power for a refinery. The station uses s...

A: Disclaimer: Since you have posted a question with multiple subparts, we will solve the first three s...

Q: A solid steel rod is 1.5 meters long and has a diameter of 20 mm. The steel rod is assume to be an e...

A:

Q: An ammonia refrigerating system has a load of 250 kW and operates at a condensing pressure of 1400 k...

A: Using thermodynamic property table of ammonia, Enthalpy at various points are calculated using linea...

Q: A confined volume of 27 moles an ideal gas (with y 1.42) goes through an expansion process so at the...

A:

Q: a) Find the moment of each of the forces shown in (Fig. 1) about point O. b) Find the total moment a...

A:

Q: If Q = 450 N and support reaction P, = 300 N, determine the force magnitude in member CJ. !3! 1m 1m ...

A: Find the magnitude of force in member Cj Where  Q = 450 N               Py = 300 N

Q: 76. All surfaces of an infinitely long heating element, having a cross section in the shape of a cro...

A: Fins are the projection protruding from a hot surface into ambient air and they are meant for increa...

Q: Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = ...

A:

Q: A reversed Carnot cycle has a refrigerating COP of 4. (a) What is the ratio Tmax/Tmin? (b) If the wo...

A:

Q: A solid steel rod is 1.5 meters long and has a diameter of 20 mm. The steel rod is assume to be an e...

A: Given   Diameter, d = 20 mm  Shear stress = 145 MPa                  G = 77 GPa      Length, L = 1.5...

Q: The motion of a particle is governed by the relation a = 4t^2, where a is in ft/^s2 and t is in seco...

A:

Q: In casting experiments performed during a certain alloy and type of sand mould it took 155 second fo...

A: A cube-shaped casting solidified in 155 seconds in a casting experiment using a specific alloy and k...

Q: Fill the blanks correctly and define

A: Given: For apinion of 15 teeth,where, Pinion is usually a two meshed gears. It is used in several  a...

Q: A press is used to punch 10 holes per minute of 30 mm diameter hole from 25 mm thick plate. Determin...

A:

Q: uppose two infinitely long flat plates, separated by 3 in. distance and 0.5 in. thickness, conducts ...

A: Givend=3in.t=0.5inV=5m/sμ=1Pa-sS.G=0.89  

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is subj...

A:

Q: Q11 Find the reactions in supports

A: