Using OSHA regulations as a guide, determine what are theaccepted safety standards for:a. Guard railsb. Exposed reinforcing steelc. Protection of openingsd. Man hoists

Q: Describe the construction of various types of hollow-core metal doors?

A: most common type of door which used in commercial and industrial uses. these door supported on hinge…

Q: Differentiate slip-critical connection and bearing type connection. When is it better to use bolts…

A: The main difference between slip critical connection and bearing type connection is about how they…

Q: Make a CONCRETE chain and make sure it is understable.

A:

Q: Manufactured scaffold planking with spans greater than 10 feet in length must be labeled to indicate…

A: According to the General Requirements of Scaffolding, Part b (1): "Each scaffold shall be designed…

Q: Observe several construction sites and ascertain details oftheir safety program. If possible, attend…

A: As a construction site trainee engineer, I visited more than 5 construction sites in the past 1…

Q: Fall prevention methods include: proper use of worksite access such as ladders and scaffolds…

A: Fall prevention method includes: Proper use of worksite access such as ladders and scaffolds for…

Q: more description about Critical safety Hazards (roof truss installation and re-sheeting work

A: The space above a room providing support to roof with help of structural member is known as roof…

Q: The initial design of a simply supported beam is shown below. The architect requested the engineer…

A:

Q: Choose the correct answer Temporary bridges are built from a-Stones b-Steel c-the wood d-Nothing…

A: The temporary bridges are mostly built by using the prefabricated steel girder, steel plates, and…

Q: All specific sizes recommended by CRSI below meet minimum requirements of ACI 318 Recommended End…

A: The Standard Specifications require that reinforcing steel hooks and bends conform to the provisions…

Q: Where Stock rails are fitted ?

A: The Stock rails are the set of switches in track, where the outer one is stock rails and inner one…

Q: Define the term Fastener Spacing?

A: Fastener Spacing : Pitch is centre to centre spacing of the fasteners in a row, measured along the…

Q: All fixed metal parts that are within_ft horizontally of the inside walls of a permanently installed…

A: The question asked is descriptive.

Q: Problem 1. Steel Pipe Column (ASTM A53 - Grade B) 10 kip axial load. 16 foot un-braced length. PIPE…

A: Axial load(P)=10 kip, Length of the column(L)=15 feet, End condition: One end fixed and other end…

Q: Why is loosening prevention important for a bolted connection? Give examples to describe measures to…

A: this question is from steel engineering  here brief discussion about bolt loosning and prevention of…

Q: Describe fire-protection procedures for structural steel members required by building codes?

A: The fire-protection procedures for structural steel members required by building codes are:

Q: Are there any regulations in the world and in Turkey for construction vibration levels? Explain.

A: There is a new regulation which was titled as "Noise Protection and Sound Insulation in Buildings"…

Q: Briefly explain why there are only two shear strength values listed for wood-to-steel and…

A: Bolts can be in single or double shear.When the bolt is in double shear two cross sections are…

Q: ere are thin shutters?

A: To find : The  types of hinges that is used where there are thin shutters. Given option :  Strap…

Q: Discussion on limitations and constraints on the use of bolts, studs, screws ( Minimum 05), and…

A: Bolt : A bolt is a type of threaded fastener having an exterior male thread that requires a…

Q: Problem 1: a) Mention the different cases of the rust on the steel members? b) Explain the different…

A: Brief Concept Introduction- Rust- Rust is an oxidation-induced coating that forms on the surface of…

Q: Determine the design strength (LRFD)

A: Solution: calculate the strength of the plates as tension members Gross area Ag = 10(0.5) = 5 sq in…

Q: Define Steel bars and how many types of stell bars and  given details of sizes of stell bars.

A: The steel bars are defined as the mesh of various steel wires used in reinforced concrete and…

Q: what is the nominal maximum load capacity of a grade 60 reinforcing bar with a diameter of 20 mm?

A:

Q: General Specification for Civil Engineering Works (1992 Edition) Clause 15.09 specifies that tying…

A: Answer Plain steel tying wire mainly used for the reinforcement adjacent to class F4 and F5 finish

Q: Would you recommend SMF or MMF for connecting two buildings 1 mile apart? Why?

A: For two buildings 1 mile apart which is 1.6 km approximately I will recommend to connect via MMF…

Q: List various types of rails and describe different rail failures with neat sketches.

A: Types of rails: Strap rail Plate rail Bridge rail Barlow rail Flat-bottomed rail Double headed rail…

Q: Find Steel Area

A: The values and diagram(figure) given in the question are as follows: f'c=20 MPa fy=400 MPa Depth of…

Q: Scaffolding

A: Scaffolding is a temporary structure used in building construction .  Scaffolding is generally made…

Q: Explain  methods for Installing Structural bolted connections recommended by standard research…

A: Methods for installing Structural bolted connections recommended by standard research Council : 1)…

Q: Write a full report about TRUSS BRIDGE: 1-INTRODUCTION 2-OBJECTIVES 3-LITERATURE REVIEW

A: Introduction: Truss bridge, the bridge with its load-bearing structures composed of a series of…

Q: AaBbC AaBbCc AaBbCc Aa T Normal Title 1 No Spac.. Heading 1 Heading 2 Subtitle Sub Paragraph Styles…

A:

Q: Explain methods for Installing Structural bolted connections recommended by standard research…

A: Bolted connections are used to join various components together to form one single unit. The joint…

Q: Please describe the general requirements of steel bar installation and the main contents of…

A: The factors that influence steel bar installation involves its mechanical properties. Steel derives…

Q: a. Use LRFD.

A: Answer: option, (c): W16x26

Q: In what type of building code article would you see a statement specifying the mandated deflection…

A: Given question In what type of building code article would you see a statement specifying the…

Q: You were then told that the whole structure will be left exposed and unprotected from all sides.…

A: For fire requirements in a building an extra cross section for fire requirements of the member must…

Workplace Safety

A workplace can be referred to as a space where people work together for the accomplishment of a common goal of the organization. Here, people can be a worker, an employee, and an employer. A person can be said to be an employer if he/she gets the job of organizational goal accomplishment through other persons, and that person gets paid for his/her service. All employees can also be referred to as workers. An employer may also hire workers of other categories which require specialized skills to finish a work. Both employees and workers along with the employer form the primary occupants of a workplace.