Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be considered.R2=10Re=0.5 0E1=12 VE1=9 VR3=10R1=10Rs=0.5 0A1.5 voltsB2.0 volts2.3 voltsD) 3.0 volts

Answered: Image /qna-images/answer/8cdb255a-d40d-46c5-9293-70126bfb3cb1.jpg

Answered: Using Superposition Theorem, what is…

Engineering

Electrical Engineering

Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be considered.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: Using the Node Voltage Method, what is the voltage v1

A: Firstly finding equivalent of two 4 ohm resistors in parallel- Req=4ll4 =2 ohm The circuit…

Q: 4. Determine the value of the current is using superposition.

A: The superposition theorem state that the response across any element is algebraic sum of response of…

Q: 4 a) Design a current divider circuit using a 50mA current source so that it provides currents of…

A: Given: The source current, Is=50 mA Current in two branches of circuit is 10 mA and 2 mA.

Q: Two 12-V batteries with internal resistance of 20Ωand 20Ω, respectively are joined in parallel and a…

A: Two 12-V batteries with internal resistance of 20Ωand 20Ω, respectively are joined in parallel and a…

Q: Q3: Suppose that the components of the circuit shown in figure below, have the following values: R1=…

A: R1=16Ω R2=18Ω R3=30Ω R4=9Ω R5=4Ω INTERNAL RESISTANCE=250Ω

Q: Find .current in the 4 resistor by using Norton theore m

A: For finding Nortons current short the 4 ohm terminals and calculate current in short circuited…

Q: In the circuit shown below V,--1 V 3V s00 ka. 48k

A: Junction Transistor (BJT) is three terminal device and three terminal are Emitter ,Base and Bipolar…

Q: 4. For the network of Figure 4, determine: a. VB b. VC c. VE d. IE e. IB f. IC g. VCE

A: The given circuit diagram is shown below:

Q: Determine the Power Dissipated in Resistor R4.

Q: 4- In the circuit in following figure, obtain y1, v2, and v3. 15 V 25 V 10 V 20 V

A: Kirchhoff's voltage law states that in a closed loop the sum of potential difference across an…

Q: Find the current through 4ohms using Loop Analysis

A: In the circuit, Find the current through 4ohms using Loop Analysis? Here 3 independent loops are…

Q: 2. Using Kirchhoff's Law, determine the currents (lı, l2, Is, la, and Is) and power delivered to the…

Q: Q4) A power supply A delivers 10 V dc with a ripple of 0.5 V r.m.s. while the power supply B…

A: The power which have the lower value of ripple factor is said to be better power supply. Ripple…

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

A: In this question we need to find voltage drop across R4 when 12 volt source is considered.

Q: 4. Use the data that you have generated for your different Voltages (the first 4 rows of the table)…

A: Current Voltage 9 4.5 15.6 7.8 2.6 1.3 18 9

Q: Suppose that the components of the circuit shown in figure below, have the following values: R1= 162…

A: given values are, R1=16Ω, R2=18Ω, R3=30Ω ,R4=9Ω, R5=4Ω Voltage across AB VAB=36R5R5+R4=3644+9true…

Q: a) Using equivalent network (find R4L which is the parallel combination of R4 and RL, this…

Q: Design and draw a series and parallel combination circuit comprising of one series resistor and two…

Q: Using the n adal voltage methed, 6ind, the current I in the cireuit shown. All resistors are in…

Q: Using branch current method, solve

A: This question belongs to circuit theory . It is based on the calculation of current in the circuit…

Q: For the circuit shown, find the current in the 32 resistor. Using: A) Loop current method. 444 * 4V

A: The solution is given below

Q: The voltages V1, V2, V3, and v4 are the node voltages corresponding to nodes 1, 3, and 4 In the…

A: For the given circuit calculate voltages of node V2 , V3 , V4 and given V1=25 volt : To calculate…

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

A: In this question, Choose the correct option What is voltage across the R4 resistance when 12V…

Q: For the Wheatstone Bridge network shown in Figure. Calculate the voltage across the points P and R.…

A: The solution can be achieved as follows.

Q: نقطة واحدة By using the experiment of series connection: the voltage at each resistance is * equal…

Q: Using superposition theorem, find the voltage across R4 for this network with all necessary steps,…

A: The circuit diagram is, Applying superposition theorem, The 12 V voltage source is short-circuited…

Q: In the following Circuit if V, = 54V and R, to the load resistance R is: 6N The maximum power…

A: Maximum power across the load resistance We are solving this problem using the Thevenin theorem.

Q: 8 V b

Q: True/False: Consider connecting a Load Resistance across R2. Loading Effect is less when voltage…

Q: The 100V source is absorbing 50w of power in the network shown in the Figur what is the value of R…

A: Given

Q: given network is having N nodes and b branches, then number of individual .4 loops are a) N. O b)…

Q: 4. Find the equivalent resistance of the given circuit. HINT: Label your nodes. Reg 362.480 2200…

Q: Q4- using SuperPositions determine the Current through the 32 resistor. 502 6v lov

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

Q: What is the resistance value of R4 for the following balanced bridge circuit? R1 802 R3 4802 100V i…

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

A: we need to find out voltage drop across R4.

Q: Q4) By using Nodal analysis, find all voltages and currents. 4 kΩ 1 k2 4 mA Vc VA VB 10 V 2 kΩ 4 k2

Q: Obtain the current flowing in the circuit in resistance(22) with Nodal Analysis Techniques.

A: For given circuit, converting current source to voltage source first

Q: 3) Using superposi hon principle to find v and the power dissipated by the 32 resistar 12 V (오 (^)6A

Q: Q4(4*2)/A/ For the network of the figure shown below, using the maximum power transfer method to the…

Q: Q3: What is your Opinion about the current ?in R4 +250V 100mA Es LOAD 3 310V +50V 50mA LOAD 2 -25V…

A: 3) The current across resistance R4 is found by using KCL. - Kirchhoff's current law states that the…

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

Q: es the voltage 6 times. Also discuss it in detail.

A: A single circuit can be interpreted in terms of voltage multiplier circuit. The circuit is shown in…

Q: Hiw Di Find.current in the 4e resistor by using Norton theore mm

Q: Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be…

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).

Question

Using Superposition Theorem, what is the voltage drop at R4 when the 12 volts source will be considered.
R2=10
Re=0.5 0
E1=12 V
E1=9 V
R3=10
R1=10
Rs=0.5 0
A
1.5 volts
B
2.0 volts
2.3 volts
D) 3.0 volts

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
The voltages v1, v2, v3, and v4 are the node voltages corresponding to nodes 1, 2, 3, and 4 in the below Figure. The value of node voltage v1 is 25 V. Determine the values of v2, v3, and v4 node voltages. The value of v2 in volts is The value of v3 in volts is The value of v4 in volts is
Since VDD = +15 V, VTH = +2 V and K = 100mA/V^2 in the circuit below, what is the ID current? (In circuit resistors The specified R value is in ohms) I want a quick solution, the method doesn't matter, the result matters
For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=3,68 kΩ VD=VS=VDS=
Plz what is the methods of this circuit. ALL methods Plz.
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VT=2.99 V, ID(on)=5.54 mA, VGS(on)=5.3 V VG=? VGS Q =? ID Q =? VDS=?
Given that Short circuit current - 5.52 A Open circuit voltage - 45.1 V Current at MPP - 5.19 A Voltage at MPP - 36.6 V Power at MPP - 190 W Number of PV cells and area of each cell - 72 cells (125mm × 125mm) Efficiency of PV module and the area of module - 14.9% efficiency (1581mm × 809mm × 35mm) Twelve (12) modules are configured into 4 strings of 3 modules in series. Two strings areput in parallel and then connected in series with another set of two strings in parallel. Determine the power at MPP under standard conditions.
Please help me solve for the total resistance, total current, and individual voltage if: VT = 30 VR1 = 7 ohmsR2 = 10 ohmsR3 = 6 ohmsR4 = 4 ohmsR5 = 8 ohmsR6 = 9 ohmsR7 = 5 ohmsR8 = 12 ohmsR9 = 3 ohmsR10 = 8 ohms
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in A?
When we want to create an 8x1 multiplexer using the circuit elements we have, which circuit will we need? a.) 7 pieces of 2x1 MUX b.) 2 pieces of 4x1MUX c.) 3 pieces 4x1 MUX d.) none e.) 4 pieces 2x1 MUX
Please help me solve for the total resistance, and total current if:Vt = 20 VR1 = 2 ohmsR2 = 5 ohmsR3 = 7 ohmsR4 = 8 ohmsR5 = 3 ohmsR6 = 4 ohmsR7 = 9 ohmsR8 = 6 ohmsR9 = 10 ohmsR10 = 7 ohms
For most of the circuits, determine all the voltages and currents necessary this usually involves:(Eth, VR1, VR2) VB,VC,VE, VCE,VCB, IB, IC,IE, (I'C)