Using the following characteristics, determine Bac at IB = 60 uA and VCe= 5V *tic (mA)87G(Saturation region), 542VCE90 μLA80 μA70 μA60 μLA50 μLA10Hitt(Active region)40 μA30 μA- 2014 -ICEO BICHO10 μA15(Cutoff region)-OμA20 VCE (V)1/8 (HA)1009080706050403020100VCE = 1 VVCE = 10 VVcs=20 VKILLL0.2 0.4 0.6 0.8(b)1.085VBE (V)65 O4575 O70 O

Answered: Image /qna-images/answer/350a6dc8-b1d6-405c-8315-1c28b6e766fa.jpg

Using the following characteristics, determine Bac at IB = 60 uA and VCe= 5V * +ic (mA) 7 G (Saturation region) 5 4 2 1 90 LA 80 μA 70 μA 60 μA 50 μA 10 40 μA 30 μA (Active region) 20 μA 10 με 15 (Cutoff region) ICEO = PICIO a=0μA 20 VCE (V) 1/8 (HA) 100 90 80 70 60 50- 40 30 20 10 0.2 0.4 0.6 (b) VCE=1V VCF = 10 V Vcs=20 V LLLL 0.8 1.0 85 65 45 75 70 VBE (V)

Using the following characteristics, determine Bac at IB = 60 uA and VCe= 5V * +ic (mA) 7 G (Saturation region) 5 4 2 1 90 LA 80 μA 70 μA 60 μA 50 μA 10 40 μA 30 μA (Active region) 20 μA 10 με 15 (Cutoff region) ICEO = PICIO a=0μA 20 VCE (V) 1/8 (HA) 100 90 80 70 60 50- 40 30 20 10 0.2 0.4 0.6 (b) VCE=1V VCF = 10 V Vcs=20 V LLLL 0.8 1.0 85 65 45 75 70 VBE (V)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter16: Inductance In Ac Circuits

Section: Chapter Questions

Problem 1PP: Inductive Circuits Fill in all the missing values. Refer to the following formulas:...

See similar textbooks

Similar questions

Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
Q16. Scientists have tried to commercialize Li metal anode materials in the past without asuccess. Recently, scientists revisited the Li metal anode and achieved a certain level ofimprovement. Please estimate the theoretical capacity of Li metal (LiLi++ e-).A. 3862 Ah/gB. 3862 mAh/gC. 26.8 Ah/gD. 13400 mAh/g
Write the following acronyms in full and Explain it main function. 1. LCD 2. PWM 3. MHz 4. RFU 5. LED 6. VIN 7. ICS 8. GND 9. STBY 10. VM
19.A crystalline silicon solar cell generates a photo-current density Jph= 400 A/m2 and saturation current density Jo = 10-8A.m-2. Calculate the open circuit voltage at room temperature (VT = 26 mv)
Using IC that is approximately equal to IE. Determine the value of R1in ohms, when VCC=17V, RC=2235 ohms, RE=335 ohms, VC=7 V and R2=6038ohm
Q6-Assuming that all of the valence electrons contribute to current flow, (a) calculate the mobility of an electron in copper and (b) calculate the average drift velocity for electrons in a 100 cm copper wire when 10 V are applied. Given( The lattice parameter of copper is 3.6151 10", copper is FCC, a = 5.89 x 105)
Draw typical schematics for: 1.BJT current mirror of 5 mA (use VCC=10V); 2.Si temperature sensor working at 10 μA; 3) Si photodetector Please note I need all three. Don't answer one and skip others. If u can't answer all kindly skip the question please
please give detail explain.. Ans : Rth = 28 ohm Vth = 92 V
Answer the following True or False: 1. A direct bandgap material absorbs more light in a given thickness than an indirect band gap material. 2. CdTe thin film solar cells make up less than 8% of the current installed photovoltaic capacity. 3. The voltage generated in a photovoltaic cell is linearly dependent on the light intensity. 4. All commercially produced photovoltaic cells use a transparent conducting oxide (TCO) as a front contact. 5. Si solar cells are used in space applications due to their higher resistance to radiation damage.
1. Differentiate the following types of PCBs? Single-layer PCB Double-layer PCB Multi-layer PCB Rigid PCB Flexible PCB Rigid Flex PCB High-frequency PCB Aluminum-Backed PCB 2. What composes a PCB? (Composition of a PCB)
Please send the answer by typing only. I don't want handwritten. The subject is ( Electronic Circuits ) Q6) What are the differences between BJT and JFET?