Using the method of components calculate the magnitude, direction, and location of the total force on the upstream face of a section of this dam 1 m wide. What is the moment of this force about O. (specific weight of the water and concrete are 1 t/m³ and 2,6 t/m³ respectively). 6.0 m 20.0 m 12.0 m P H.5m -12 m

Using the method of components calculate the magnitude, direction, and location of the total force on the upstream face of a section of this dam 1 m wide. What is the moment of this force about O. (specific weight of the water and concrete are 1 t/m³ and 2,6 t/m³ respectively). 6.0 m 20.0 m 12.0 m P H.5m -12 m

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.7CTP

See similar textbooks

Similar questions

The concrete dam of trapezoidal cross section is shown with T = 1m, B = 4.3m, H = 9m and h = 6m. The unit weight of the concrete is 24??⁄?3. For the given conditions, evaluate the resisting moment of the dam to overturning in kN.m per meter length of dam. Unit of the Correct Answer: kN-m
Estimate the equivalent hydraulic bearing for flow in the vertical direction. Suppose that k1= 10 x 10^-4 cm/s, k2 = 5.0 x 10^-4 cm/s, k3 = 6.0 x10^-4 cm/s, k4 =3.0 x 10^-4 cm/s, H1 = 2.5 m, H2 =1.5 m, H3 =1.0m, H4 = 2.5 m.
A dam is inclined at an angle of 30\deg from the vertical and has the shape of an isosceles trapezoid 80 ft wide at the top and 40 ft wide at the bottom and with a slant height of 60 ft. Find the hydrostatic force on the dam when the water level is at the top of the dam. (Round your answer to the nearest whole number. Assume that the weight density of this water is 62.5 lb/ft3.)
A masonry dam has a trapezoidal cross section, 25 m high, crest width of 3 m and base length 18 m. The upstream face slopes down 12 m in 25 m and the downstream faces slopes down 3 m in 25 m. If the water at the upstram face stands flushed with the crest and assuming no hydrostatic pressuruplift. Compute the location point along the base (measured from the toe) where the resultant force intersects it. The specific gravity of concrete is 2.40. a.5.24 m b.2.67 m c.5.44 m d.2.57 m
Answer the following: a. hydrostatic force acting on a wall b. weight of dam if the unit weight of concrete is 23.54 kn/cum c. overturning moment d. location of the resultant measured from the toe of the dam
a. Which of the following most nearly gives the factor of safety against sliding? b. Which of the following most nearly gives the factor of safety against overturning? c. Which of the following most nearly gives the pressure intensity at the heel of the dam?
A dam shown in figure has water 2.7 m high on the vertical upstream side. If unit weight of concrete is 23.5 kN/cu.m, determinea. Minimum width of the base that the resultant falls within the middle thirds. Neglect hyrostatic uplift.b. Minimum coefficient of friction to prevent sliding
5. What is the factor of safety against overturning for the triangular dam? Determine the pressure distribution at the base of the dam. Neglect hydrostatic uplift. Use unit weight of concrete 24kN/m³.
Determine the pressure intensity at the heel of a trapezoidal dam having a dimension of 4 m on top, 18 m at the bottom and 24 high with water 20 m deep on its vertical side. Unit weight of the concrete is 23.9 kN/m^3. No hydrostatic uplift.
A masonry dam has a trapezoidal cross-section 25 m high, crest width of 3 m and base length 18 m. The upstream face slopes down 12 m in 25 m and the downstream faces slopes down in 3 m in 25 meters. If the water at the upstream face stands flushed with the crest and assuming no hydrostatic pressure uplift. Compute the location point along the base (measured from the toe) where the resultant force intersects it. The specific gravity of concrete is 2.40
A gravity dam of trapezoidal cross-section with one face vertical and horizontal base is 22 m high and has a thickness of 4 m at the top. Water upstream stands 2 m below the crest of the dam. The specific gravity of masonry is 2.4. FS(sliding) = 1.5
Determine the pressure intensity on the base of the Dam shown. Consider without hydrostatic uplift. Unit weight of concrete is 24 kN/m^3.