Using your results in step 1, design and build the 2-level voltage level meter in Figure 5. Note that voltage node V₁ in the voltage divider (Figure 4) is connected to the inverting input of one of the op-amps and voltage node V₂ in the voltage divider is connected to the inverting input of the other op- amp. Use the equation in the "Light Emitting Diodes" supplement to determine values for Rlimiting so that the current through each LED (when on) is 10 mA, as specified in the supplement.

Using your results in step 1, design and build the 2-level voltage level meter in Figure 5. Note that voltage node V₁ in the voltage divider (Figure 4) is connected to the inverting input of one of the op-amps and voltage node V₂ in the voltage divider is connected to the inverting input of the other op- amp. Use the equation in the "Light Emitting Diodes" supplement to determine values for Rlimiting so that the current through each LED (when on) is 10 mA, as specified in the supplement.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Similar questions

In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
When OP-AMPs are considered ideal in the circuit: a) What is V voltage? b) What is the equivalent resistance of the region inside the rectangle?
Design an op amp circuit to perform the following operation: vo = 3.5v1 - 2.5v2. All resistance must be < = 100k. The power supply should be +15V and -15V. Let v1 = 2V and v2 = 1V.
R = 10 kohms, two op-amps are ideal and working in the linear operation range Find the currents i1,i2,i3,i4,i5,i6,i7,i8
Assume all op amps are ideal.1) What is the name of the op amp circuits in the dashed box?2) Explain briefly what is the purpose of having the op amp circuits in thedashed box.3) What are the input resistances seen by VA, and by VB?4) What is the output resistance?5) What is Vo in terms of VA and VB, assuming all resistors in this circuit havethe same resistance?
For this op amp, an equation needs to be made for V0 = Va + Vb. I thought it was -4(Va) + 4(Vb) as the difference, but that doesn't seem to be correct. The voltage limits for the output voltage are -0.8 V less than or equal to Vo less than or equal to 3.2 V. Can you show how to set up the equation for V0?
Calculate the voltage of an inverting op-amp summing amplifier for the following sets of resistors. Use Rf = 1 MΩ in all casesa) V1 = 1V, V2 = 2V, V3 = 3V, R1 = 500 kΩ, R2 = 1MΩ, R3 = 1 MΩb) V1 = -2V, V2 = 3V, V3 = 1V, R1 = 200 kΩ, R2 = 500 kΩ, R3 = 1 MΩ
this is good and the answer is correct but what i dont understand is how did u know there is no current through the op amp and if there was no current going through since v=ri if i=0 r and v should be 0 too no? so why did we ignore r2 and use v2? and why did u take v0 at that place? PLEASE DO NOT RE-SOLVE AND JUST ANSWER MY INQUIRY. THANK YOU
Without changing the locations of the loads in the figure,a) Draw a suitable diagram to measure the active power drawn bythe load Z2 ONLY using a W-m.b) According to your diagram, express the absolute method errorin power measurement by defining the required magnitudes.(Give sufficient explanation).
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
proof the equation 10.8 which represents the gain of inversting amplifer ... the proof is already exist in page 621 but there are some expressions were missed before the equation 10.7, you should start this proof from the begining and adding that missed expressions.