Obtain:V guti.the system transfer function H(s) =inMatLab plot of the magnitude and phase response of the system transfer functionH(s) and locating the half-power points (3-dB point) and phase angle on themagnitude and phase response curves.i.V outi.LTSpice plot of the magnitude and phase response of the system transfer functionand locating the half-power points (3-dB point) and phase angle on the magnitude andphase response curves.For the following filter:+HIVin+Vout-с %3D0.1uF L %3D 25.266mH R31002

Since we are not allowed to solve software-based problems. so, solving the first part only.

Answered: V out Vin i. the system transfer…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the parallel RLC circuit below, (a) derive the expression for the resonantfrequency, the half power frequencies, the bandwidth, and the quality factor for the transfer function of Vout/Iin in terms of the circuit parameters R, L and C, and (b) Compute the quantities in (a) if R = 1kohm, L = 10mH and C = 100uF.
The voltage transfer function of the prototype bandpass filtershown isH(s)=(1Q)ss2+(1Q)s+1. Show that if the circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(1Q)(skf)(skf)2+(1Q)(skf)+1.
2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
Obtain the transfer function Vo (s) / Vi (s) for the electric circuit given in the figure.You can find the amplitude value of the transfer function at high frequencies of the circuit.If it works, calculate approximately. System-owned transferDraw the Bode diagram of the function.
How to calculate the Q-factor and bandwidth of the series and parallel R-L-C circuits?
We have two filters with transfer functions H 1 (f) and H 2 (f) cascaded in the order 1– 2. Give the expression for the overall transfer function of the cascade. Repeat if the transfer function magnitudes are expressed in decibels denoted as |H 1 ( f )| dB and |H 2 ( f )| dB. What caution concerning H 1 ( f ) must be considered?
A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
The Bode plot of a transfer function H is shown in Figure 1. What is H in its standard form? In your estimate, what is the magnitude of the transfer function H at as shown in Figure 1? Answer should be given in its original value not the dB value. Note that HdB = 20 log H, where H is the original value.
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 42.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit.NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
A transfer function is given by H( f )= 10 1−j( f/500 ) Sketch the asymptotic magnitude and phase Bode plots to scale. What is the value of the halfpower frequency?
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 7.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit. NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
An R–L–C series circuit has a resonant frequency of 1.2 kHz and a Q-factor at resonance of 30. If the impedance of the circuit at resonance is 50 ohm determine the values of the inductance, and the capacitance. Also find the bandwidth, the lower and upper half-power frequencies and the value of the circuit impedance at the half-power frequencies.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

V out Vin i. the system transfer function H(s) =