Various parameters of Schering bridge are given as follows. The voltage supply of 2 kHz is connected to terminals A and C and detector to points B and D. Arm AB comprises the unknown Resistor R1 and capacitor C1. Arm BC consists of resistor R2 of 18k 2. Arm DA consists of capacitor C2 of 0.06 µf. Arm CD has R3 of 1.5k2 and C3 of 2nf are in parallel. Calculate (i) the capacitance (C1) (ii) the equivalent series resistance (R1) and (iii) dissipation factor. Also draw the schematic diagram.

Various parameters of Schering bridge are given as follows. The voltage supply of 2 kHz is connected to terminals A and C and detector to points B and D. Arm AB comprises the unknown Resistor R1 and capacitor C1. Arm BC consists of resistor R2 of 18k 2. Arm DA consists of capacitor C2 of 0.06 µf. Arm CD has R3 of 1.5k2 and C3 of 2nf are in parallel. Calculate (i) the capacitance (C1) (ii) the equivalent series resistance (R1) and (iii) dissipation factor. Also draw the schematic diagram.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the...

See similar textbooks

Similar questions

Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
Give examples for the following: A.) 1 example of DC analysis of darlington pair solved problem. B.) 1 example of AC analysis of darlington pair solved problem.
2. The output impedance of 600 ohms radio transmitter with signal strength reading on a meter of impedance 75ohms by 0.81 neper of unbalance non-symmetrical Pi-pad attenuator circuit. Determine the required resistor values to design this attenuator.
Determine the required values of R1, R2, Rc, and RE. Also, determine the expected output voltage if the input voltage is equal to 0.001 Vrms. GIVEN: Zi = 1145.66 ohms Zo = 3.3 Kohms Beta = 80 Vcc = 20V R1 + R2 = 43.7 Kohms Av = 167.43 Ai = 58.13
Figure 1 shows a well-known circuit configuration with the bypassed source resistor using an n-channel D-MOSFET with yos = 20µS. (iv) Calculate transconductance, gm and rd. (v) Calculate the input, Zi and output impedance, Zo for the circuit. (vi) Prove that the equation for the no-load Gain, AvNL, for the circuit is as follows: AvNL = -gm (RD X rd / RD + rd) (vii) Calculate the no-load gain AVNL. (viii) Find the value of VoNL if Vi = 30 mV.
Q.1. A power suppply having 220 V AC input and two fixed outputs as 10 V DC and 20 V DC is requested from you. For this purpose, a transformer with 220 V AC input / 15 V AC output, some capacitors, some silicon diodes, and zener diodes are presented.a) Design your power supply and point out DC voltage outputs b) Explain the operation of the network and all the components used in the design .c) Calculate and plot input and output signals of the network.Hint: For design, remember clipper, clamper, rectifier,voltage multiplier and zener circuits
The gain of vertical deflection amplifier in CRT is 90. If an input signal of 110mV is applied, it will produce electrical field of 33V/cm and vertical deflection of electrons beam on the center of plates of 4.31x10-3 cm with an angular deflection given by arctan (0.0137). The electrons enter the plates with a velocity of 3.2479x109 cm/sec, and deflection sensitivity of 0.055cm/V. Determine: 1) The dimensions of vertical deflection plates {long, a part (l,d)}. 2) The distance from the end of deflection plates to the screen. { 2.5cm, 0.3cm, 38.49cm}
A. Give 3 possible problems rn that can relate on electrical engineering and give a solution that can aware public.
A 565 IC PLL has an external resistor R1 of 1.2 kΩ and a capacitor C1 of 560 pF. The power supply is 10 V. (a) What is the free-running frequency? (b) What is the total lock range?
-BJT AC ANALYSIS -USE EXACT ANALYSIS - show diagram answer c1 only thanks
just need fınal answer Since Vi = 20 mV, Vcc = 25 V, RB = 470 kΩ, RC = 3.2 kΩ, RE1 = 470 Ω, RE2 = 1.2 kΩ, RL = 42 kΩ and β = 110 in the circuit in the figure, the value of the output voltage (Vo) find it. NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The output impedance of the transistor (r0) will be neglected. a. -197,96 mV b. -222,71 mV c. -98,98 mV d. -148,47 mV e. -123,73 mV f. -173,22 mV g. -247,45 mV h. -74,24 mV
Find the voltage, voltage gain, input and output resistances of the circuit (RS=RC=RE=2k,RB1=150k,RB2=25k,β=100, VBE=0.6V, VT=26meV)