Vector A has a magnitude of 6 units and it is in the direction of positive X-axis vector B has a magnitude of 4 units and lies in XY-plane making an angle 30 with X- axis Find AXB

Q: The 37-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of…

A:

Q: n a reheat cycle steam enters the high pressure turbine at 40 bar and 400°C. It expands isentropic…

A: Given:P1=40 barT1=400°CP2=P3=6 barT3=400°C

Q: Q2/ Suppose we are told that the acceleration a of a particle moving with uniform speed v in a…

A:

Q: (a) Determine the radius of curvature of the trajectory and the time rate of change of the speed of…

A:

Q: Completely solve and box the final answer. Write legibly 4. Compute the required size of the motor…

A:

Q: The mass center G of the 1235-kg rear-engine car is located as shown in the figure. Determine the…

A: Given Data The mass of the car is:m=1235 kg To find: The normal force under each of the front…

Q: 18-53. The two 12-kg slender rods are pin connected and released from rest at the position = 60°. If…

A:

Q: The 15 lb suitcase is released from rest at C. After it slides down the smooth ramp, it strikes the…

A: Given data: WA=15 lbWB=10 lbe=0.3μ=0.4 Need to determine the velocity of each suitcase just after…

Q: Give the answer with proper explanation why you chose that specific option. Thank you

A: Given: Here is the torque curve is shown here, To find: Determine the representation of Torque…

Q: Show from the following data taken for the automobile test performed on a 4 cylinder gasoline engine…

A: Given data Fuel intake = 9.78 lb/hourBrake output = 36.5 HPSpecific gravity of gasoline at 60°F =…

Q: Low thermal conductivity coatings on turbine blades protect the blades from hot gas by:

A: This question is based on the concept of coatings on turbine blade.

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: Given: Let us consider the given statements, 1. High cutting temperature is undesirable because it…

Q: 5.1 kg/s of air enters the impeller of a centrifugal compressor at a stagnation pressure of 101.3…

A:

Q: Compute for the vertical reaction at the hinged support at C. Given the following data and figure:…

A: P1=9 NP2=17 NF1=12 Nx=2 mz=5 my=7 m

Q: the magnitude of the velocity is known as the speed and it is generally expressed in units of m/s^2…

A: GIVEN DATA- A QUESTION GIVEN ABOUT UNIT OF VELOCITY AND SPEED  WE TO GIVE ANSWER AS TRUE OR FALSE

Q: 3 5

A: Given: Let us consider the given image, To find: The view factor for F34.

Q: 3) A point mass is attached to one end of a beam levered against a spike which acts as the pivot.…

A:

Q: Water at 40 °C is pumped from an open tank through 200 m of 50-mm-diameter smooth horizontal pipe as…

A: The pressure encountered by a fluid on the suction side of a centrifugal pump is measured by NPSH,…

Q: A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen 4.8%,…

A:

Q: Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

A:

Q: diagram. This force causes both suitcases to slide to the right with a coefficient of kin bases and…

A:

Q: Q1) Draw the sheering force and bending moment diagrams for fig1 2kN 20KN 10kN 1m 1m 1m FBD 10kN…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: The following figure shows an epicyclic gear train (EGT) having two inputs. The sun gear 2 rotates…

A:

Q: 2. The diameter of a 3 meter pipe decreases from 450 mm to 150 mm. If the velocity is to decrease…

A: Diameter at the bigger end =450 mmDiameter at the smaller end =150 mmLength of the pipe, L=3 m =3000…

Q: Refrigerant 22 is the working fluid in a Carnot refrigeration cycle operating at steady state. The…

A:

Q: A B

A:

Q: The 520-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: The data table below shoes the dry-bulb and wet bulb temperatures measured with a psychrometer on…

A: Given data  Day 1 Dry bulb temperature = 0°C Wet bulb temperature = -5° C Day 2 Tdbt = 5°C Twbt =…

Q: Initially at rest, A Mitsubishi Pajero and a Toyota Vios are connected by a tow cable. The winch on…

A: Given: MA = 2.5 Mg MB = 1.25 Mg L = 5 m Vrel = 2m/s   Note: FBD has not much relevance for this…

Q: An axial load P is supported by the short steel column shown in the figure. The column has a…

A: Given that, Axial load = P Cross-sectional area of column = Acolumn=13,300 mm2 Allowable average…

Q: Q2.B/ Suppose we are told that the acceleration a of a particle moving with uniform speed v in a…

A:

Q: Refrigeration is desired at a Temperature of -5.6°C (minus 5.6 degrees C). Heat is rejected at a…

A: Given   Maximum temperature, Tmax = -5.6oC = 267.4 K   Minimum temperature, Tmin = 36.7oC = 309.7 K…

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A: GIVEN DATA-   A DIESEL CYCLE GIVEN  p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, Compression ratio r…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: The mass of the concrete block shown in the figure is 5 kg and the spring stiffness is 25 kN/m. A…

A: Given data: m=5 kgmo=0.15 kgk=25 kN/mvbi=500 m/svbf=-80 m/s Need to determine the resulting motion…

Q: 6. Find the C.O.P. of a refrigeration system if the work input is 30 KJ/kg and refrigeration effect…

A: Given, Work input to the refrigeration system = W = 30 kJ/kg Refrigeration effect = Q1 = 120 kJ/kg…

Q: Refrigerant 22 is the working fluid in a Carnot refrigeration cycle operating at steady state. The…

A:

Q: Consider the case of a model of a hydroelectric dam for which it is required developing two…

A: Given questions: We have to find the parameters : Hydraulic Power and Empty Time  The given question…

Q: The name for the process in which water vapor changes back into a liquid is deposition sublimation…

A:

Q: Refrigerant 22 is the working fluid in a Carnot vapor refrigeration cycle for which the evaporator…

A:

Q: 1/2 Determine the magnitude of the vector sum V = V₁ + V₂ and the angle 0, which V makes with the…

A: Given data as per question v1 =10 units v2 =12 units

Q: The 18-lb object is travelling at a speed of 8 ft/s when the force of 15 lb is applied in the same…

A:

Q: Relationship between fluid flow and convection heat transfer

A: The motion of the fluid subjected to the unbalanced forces is called as fluid flow. As long as the…

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A: Draw the P-V diagram of cold air standard diesel cycle.

Q: 18-58. The slender 6-kg bar AB is horizontal and at rest and the spring is unstretched. Determine…

A:

Q: soccer player's head. After the soccer player heads the ball, it has a velocity of 30 fps at 20° to…

A:

Q: A thin steel cylinder 1.3 m long is subjected to internal pressure; the change in volume owing to…

A: When pressure is applied to a pipe, hoop stress occurs along its circumference. The axial direction…

Q: 3 in. + 3 in. + 3 in. 2 in. -3 in.3 in.- 6 in. X

A:

Q: Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given…

A:

Q: A Particle undergoes simple harmonic motion with a freque e displacement X at any time (t) for the…

A: